Upright AB46 C Скачать руководство пользователя страница 30

Страница: 30 / 148

Section

3-12

AB46 Work Platform

Maintenance

3.10

3.10 Drive Pump Settings
(Figure 3-12)

NOTE: Pump is properly adjusted at factory. Pump

settings should only be checked if pump failure is

suspected.

MAIN RELIEF VALVES

Main relief valves "A" and "B" should be bench tested off

the machine.

NOTE: Main relief valves should be adjusted to

5300 PSI.

PRESSURE OVERRIDE VALVE

1. Position machine on a firm level surface.
2. Disconnect brake solenoid on hydraulic manifold to

allow brakes to remain locked.

3. Connect 6000 PSI pressure gauges at gauge port "A"

and gauge port "B".

4. With engine running at normal operating RPM,

position drive joystick control to full forward.

5. Adjust pressure override valve so pressure gauge "A"

reads 4900 PSI. Turning pressure override adjust-

ment screw clockwise increases pressure and

turning counterclockwise decreases pressure.

6. Position drive joystick control to full reverse.
6. Check pressure reading on pressure gauge at "B".

Pressure readings should be the same.

Figure 3-13: Hydraulic Pump

Gauge Port "B"

Gauge Port "A"

"A" Pressure

Relief Valve

"B" Pressure

Relief Valve

PUMP REMOVAL

1. Mark, disconnect and plug the hose assemblies.
2. Mark and disconnect the electric cables.
3. Remove hardware which secures power unit and

remove from chassis.

PUMP INSTALLATION

1. Install power unit using hardware previously re-

moved.

2. Unplug and reconnect the hydraulic hoses.
3. Reconnect the electric cables.
4. Fill the tank with clean hydraulic fluid.
5. Check the oil level in the hydraulic tank before

operating the work platform.

6. Operate the pump and check for leaks and proper

operation.

7. Replenish hydraulic fluid if necessary.

IMPORTANT: If replacing the pump, be sure the

pump and hydraulic tank are filled with oil before

starting the engine. Damage to the pump may

occur if it is run without first being filled with oil.

Figure 3-12: Pressure Override Valve

Pressure Override

Valve Adjusting

Screw

Horsepower

Limiter

Содержание AB46 C





















































































































































Результаты поиска

Содержание AB46 C

Отзывы:

Похожие инструкции для AB46 C

Бренды по названию

Популярные бренды

Upright AB46 C, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание AB46 C

Отзывы:

Похожие инструкции для AB46 C

Бренды по названию

Популярные бренды