Upright AB46 C Скачать руководство пользователя страница 33

Страница: 33 / 148

Section

3-15

AB46 Work Platform

Maintenance

3.13 TORQUE HUBS

Note: Change oil in torque hubs after the first 50

hours of operation. Change every 2000 hours there-

after.

1. Remove torque hub from drive assembly (refer to

"Torque Hub Removal" section).

2. Remove drain plug from underside of torque hub

and drain oil from unit.

3. Replace drain plug.
4. Remove fill plug from top side of torque hub.
5. Remove fill level plug from side of hub.
6. Fill unit with 90 wt. gear oil until oil comes out fill

level plug opening (1/2 full).

7. Replace fill level plug. Replace fill plug.
8. Replace torque hub.

Figure 3-16: Torque Hub

3.13

ASSEMBLY

1. Assembly is reverse of disassembly
2. Apply grease to one side of thrust plate to hold it in

place.

3. Using clean hydraulic oil, thoroughly lubricate and

install cylinder block assembly. Install retaining ring.

Installation

NOTE: Torque all hardware to torques listed on

page 3-32 unless otherwise specified.

1. Install motor using hardware previously removed.
2. Install hydraulic oil lines.
3. Operate machine slowly for a short time to clear air

from hydraulic system. If necessary replenish oil

tank.

4. Check for leaks.
5. Operate machine to check for proper motor opera-

tion.

Содержание AB46 C





















































































































































Результаты поиска

Содержание AB46 C

Отзывы:

Похожие инструкции для AB46 C

Бренды по названию

Популярные бренды

Upright AB46 C, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание AB46 C

Отзывы:

Похожие инструкции для AB46 C

Бренды по названию

Популярные бренды