Upright AB46 C Скачать руководство пользователя страница 22

Страница: 22 / 148

Section

3-4

AB46 Work Platform

Maintenance

3.3 Battery Maintenance

Hazard of explosive gas mixture. Keep

sparks, flame, and smoking material away

from battery.
Always wear safety glasses when working

with batteries.
Battery fluid is highly corrosive. Thoroughly

rinse away any spilled fluid with clean

water.

BATTERY INSPECTION AND
CLEANING

Check battery fluid level daily, especially if work plat-

form is being used in a warm, dry climate. If required,

add distilled water ONLY. Use of tap water will shorten

battery life.
The battery should be inspected regularly for signs of

cracks in the case, electrolyte leakage and corrosion of

the terminals. Inspect cables for worn spots or breaks in

the insulation and for broken cable terminals.
Clean the battey when it shows signs of corrosion at the

terminals or when electrolyte has overflowed during

charging. Use a baking soda solution to clean the

batteries, taking care not to get the solution inside the

cells. Rinse thoroughly with clean water. Clean battery

and cable contact surfaces to a bright metal finish

whenever a cable is removed.

Hazard of explosive gas mixture. Keep

sparks, flame, and smoking material away

from battery.
Always wear safety glasses when working

with batteries.
Battery fluid is highly corrosive. Thoroughly

rinse away any spilled fluid with clean

water.

3.3

BATTERY CHARGING

Charge the battery only in a well ventilated

area.
Do not charge the battery when the work

platform is in an area containing sparks or

flames.
Permanent damage will result if the battery

is not immediately recharged after dis-

charging.
Never leave the charger unattended for

more than two days.
Never disconnect the cables from the

battery when the charger is operating.
Keep the charger dry.

Charge battery as follows:
1. Check the fluid level. If the electrolyte level is lower

than 3/8 in. (10mm) above the plates, add clean,

distilled water only.

2. Connect the charger plug to a properly grounded

outlet of the proper voltage and frequency.

3. Use a charger which turns off automatically when

the batteries are fully charged.

Содержание AB46 C





















































































































































Результаты поиска

Содержание AB46 C

Отзывы:

Похожие инструкции для AB46 C

Бренды по названию

Популярные бренды

Upright AB46 C, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание AB46 C

Отзывы:

Похожие инструкции для AB46 C

Бренды по названию

Популярные бренды