Upright AB46 C Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 148

background image

Section

3-16

AB46 Work Platform

Maintenance

Removal

1. Park the work platform on firm level ground and

block the wheels to prevent the work platform from

rolling.

2. Disconnect battery negative terminal.
3. Loosen the wheel lug nuts on the torque hub to be

removed.

4. Raise the rear of the work platform using a 2-ton jack.
5. Position two 2-ton jack stands under the rear axle to

prevent the work platform from falling if the jack fails.

6. Remove the wheel nuts and wheel.
7. Disconnect hydraulic brake line from brake.

Clean all fittings before disconnecting the

hose assemblies.
Plug all port holes and hose assemblies

IMMEDIATELY to prevent contamination

from dust and debris.

8. Remove 90° fitting from side of torque hub.
9. Mark and remove hoses from drive motor.
10. Remove mounting bolts from drive motor.
11. Separate drive motor from brake. Discard gasket.
12. Separate brake from torque hub. Discard gasket.
13. Remove 1/2-20 nuts and washers from torque hub.
14. Remove torque hub.

IMPORTANT: Note location of 90° fitting on torque

hub body. Hub must be installed with fitting in same

position.

Figure 3-17: Torque Hub Assembly

3.13

Installation

IMPORTANT: Hub must be installed with 90° fitting

in same position as when it was removed.

NOTE: Torque all hardware to torques listed on page

3-32 unless otherwise specified.

1. Install torque hub using 1/2-20 nuts and 1/2 wash-

ers.

2. Remove plug from 90° fitting and install fitting in

side of torque hub. Point fitting towards rear of hub.

3. Using SAE 90W weight gear lube with EP additive,

fill torque hub through top plug hole in rear cover

until oil comes out of 90° fitting in side. Plug 90°

fitting and top of rear cover.

4. Install new gasket and brake.
5. Install new gasket and drive motor.
6. Secure assembly using washers and bolts.
7. Connect hydraulic brake lines.
8. Connect hoses to drive motor.
9. Install wheels. Torque lug nuts to 90ft. lbs. (123

Nm).

10. Bleed brake lines if necessary.
11. Remove jack stands and lower rear end.
12. Connect battery terminal.
13. Check function of brake.

3.5

1. Motor

2. Brake

3. Gasket

4. 90° Fitting

5. Torque Hub

«
...
32
33
34
35
36
...
»

Содержание AB46 C





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для AB46 C

Бренд: Ballymore Страницы: 72

Бренд: HSS Hire Страницы: 10

Бренд: Skyjack Страницы: 88

SJ6832 RTE Series

Бренд: Skyjack Страницы: 112

Бренд: Skyjack Страницы: 122

Бренд: NIFTYLIFT Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды