Upright AB46 C Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 148

background image

Section

3-24

AB46 Work Platform

Maintenance

3.15 Master Cylinder

REMOVAL

1. Raise elevating assembly until master cylinder pins

are accessible.

2. Support the cage assembly (refer to Figure 3-1).
3. Remove rod end retaining bolt and rod end pin.
4. Mark and disconnect hoses and immediately cap

the openings to prevent contamination.

5. Using a metal drift, remove rod end pin.
6. Remove base end pin retaining bolt and pin.
7. Carefully remove master cylinder.

DISASSEMBLY

Note: Provide a clean work area for this operation,

and observe clean assembly practices. Seals and

hydraulic cylinder components are highly sensitive to

contamination that may not be visible to the naked

eye.

1. Remove set screw from cylinder tube and unscrew

head from cylinder.

2. Carefully pull rod assembly from cylinder.
3. Clamp rod end in vise and turn piston off of rod.

NOTE: Piston is loctited (Loctite #277) onto rod.

4. Slide the head off of the rod.
5. Remove seal kit components (wipers, rod seals, o-

rings and backup rings) from head and piston.

6. Thoroughly clean all parts with solvent. Rinse the

inside of the tube and allow to drain. A high pres-

sure rinse and wipe with a lint free rag is preferable.

7. Inspect the rod, head, piston, and tube for

scratches, pits, or polishing. Check seal groves and

sealing surfaces. Scratches or pits deep enough to

catch the fingernail are unacceptable, replace the

cylinder. Polishing is a sign of uneven loading.

When this occurs, the surface should be checked for

roundness. Cylinders not round within .007" should

be replaced.

ASSEMBLY

NOTE: Torque all hardware to torques listed on page

3-32 unless otherwise specified.

1. Lubricate all components and seals with clean

hydraulic oil prior to assembly.

Note: To avoid cutting the seals, do not use sharp

edged tools during seal replacement. After installing

seals allow at least one hour for the seals to elasti-

cally restore to their original shape before assembling

cylinder.

2. Install new seal kit to piston and head.
3. Lubricate rod wiper and seal with hydraulic oil and

slide head onto rod.

4. Clean threaded end of rod using loctite primer.
5. Using loctite #277, install piston onto rod.
6. Lubricate seals on piston and head with hydraulic

oil.

7. Carefully slide rod assembly into cylinder.
8. Thread head into cylinder. Be sure hole for set

screw aligns with hole in cylinder tube.

9. Clean set screw in loctite primer. Install set screw

using loctite #242.

INSTALLATION

1. Follow steps from "REMOVAL" section in reverse

order to install cylinder.

2. Remove boom support.
3. Slowly raise and lower boom several times. Check

hydraulic connections for leaks. Check for proper

slave cylinder operation.

Figure 3-24: Master Cylinder

1. Rod Wiper

2. Rod Seal

3. Backup

4. Static Seal

5. Piston Seal

A. Rod

B. Head

C. Piston

D. Cylinder

E. Set Screw

3.15

Seal kit (068454-010) includes:

«
...
40
41
42
43
44
...
»

Содержание AB46 C





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для AB46 C

Бренд: MAHA Страницы: 30

Quick Raiser 205

Бренд: Molift Страницы: 20

Бренд: Kleton Страницы: 5

Бренд: Kleton Страницы: 5

Бренд: JLG Страницы: 44

Бренд: JLG Страницы: 150

Бренд: Sinoboom Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды