background image

www.uponor-usa.com • www.uponor.ca

36

Uponor Climate Co˘ntrol™ Zoning System Installation Guide

37

Section 10

System Maintenance 

Regular system component checks are recommended  
to optimize performance. This system requires no  
maintenance, but check system status regularly.

Thermostat Batteries

The thermostats are powered by batteries. Replace the 
batteries of the thermostat when the symbol 

 appears.

Base Unit

The Power LED of the Base Unit is always lit. When it 
blinks, this means that an alarm has been triggered.  
Open the controller cover. The LED of the channel from 
which the alarm originated is blinking rapidly. See 

Section 

11: Troubleshooting

.

Automatic Exercise Function

The system is fitted with an automatic exercise function. 
Pump and actuators run every six days to prevent them 
from seizing.

If system is fitted with an interface, the exercise 
function may be activated at any time.

Cleaning the Zoning System

Use a dry soft cloth to clean the Zoning System 
and its components.

Interface Maintenance

• Check for alarms.
• Check the Information Menu every six months.
•  Use a dry soft cloth to clean the Zoning System and 

all its components.

Disposal of the Product

The Zoning System is made up of various recyclable 
components. Dispose of them properly.

STOP

Содержание C-55
































Отзывы: