background image

IM_1GSW-02

www.ueonline.com

13

U N I T E D   E L E C T R I C   
C O N T R O L S

180 Dexter Ave., Watertown, MA  02472 USA
617 926-1000    Fax 617 926-2568

www.ueonline.com

RECOMMENDED PRACTICES AND WARNINGS 
United Electric Controls Company recommends careful consideration 
of  the following factors when specifying and installing UE pressure and 
temperature units. Before installing a unit, the Installation and Maintenance 
instructions provided with unit must be read and understood. 

•  To avoid damaging unit, proof  pressure and maximum temperature limits 

stated in literature and on nameplates must never be exceeded, even by 
surges in the system. Operation of  the unit up to maximum pressure or 
temperature is acceptable on a limited basis (e.g., start-up, testing) but 
continuous operation must be restricted to the designated adjustable range. 
Excessive cycling at maximum pressure or temperature limits could reduce 
sensor life.

•  A back-up unit is necessary for applications where damage to a primary 

unit could endanger life, limb or property. A high or low limit switch is 
necessary for applications where a dangerous runaway condition could 
result.

•  The adjustable range must be selected so that incorrect, inadvertent or 

malicious setting at any range point cannot result in an unsafe system 
condition.  

•  Install unit where shock, vibration and ambient temperature fluctuations 

will not damage unit or affect operation. When applicable, orient unit so 
that moisture does not enter the enclosure via the electrical connection. 
When appropriate, this entry point should be sealed to prevent moisture 
entry.

•  Unit must not be altered or modified after shipment. Consult UE if  modi-

fication is necessary.  

•  Monitor operation to observe warning signs of  possible damage to unit, 

such as drift in setpoint or faulty display.  Check unit immediately.

•  Preventative maintenance and periodic testing is necessary for critical 

applications where damage could endanger property or personnel.

•  Electrical ratings stated in literature and on nameplate must not be 

exceeded. Overload on a switch can cause damage, even on the first cycle.  
Wire unit according to local and national electrical codes, using wire size 
recommended in installation sheet.

•  Do not mount unit in ambient temp. exceeding published limits.

LIMITED WARRANTY

Seller warrants that the product hereby purchased is, upon delivery, free from 
defects in material and workmanship and that any such product which is found 
to be defective in such workmanship or material will be repaired or replaced 
by Seller (Ex-works, Factory, Watertown, Massachusetts. INCOTERMS); provided, 
however, that this warranty applies only to equipment found to be so defec-
tive within a period of  24 months from the date of  manufacture by the Seller 
(36 months for the Excela, Spectra 12 and One Series products; 18 months 
for Temperature Sensors). Seller shall not be obligated under this warranty for 
alleged defects which examination discloses are due to tampering, misuse, 
neglect, improper storage, and in any case where products are disassembled 
by anyone other than authorized Seller’s representatives. EXCEPT FOR THE 
LIMITED WARRANTY OF REPAIR AND REPLACEMENT STATED ABOVE, SELLER 
DISCLAIMS ALL WARRANTIES WHATSOEVER WITH RESPECT TO THE PRODUCT, 
INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR 
ANY PARTICULAR PURPOSE. 

LIMITATION OF SELLER’S LIABILITY

Seller’s liability to Buyer for any loss or claim, including liability incurred in 
connection with (i) breach of  any warranty whatsoever, expressed or implied, 
(ii) a breach of  contract, (iii) a negligent act or acts (or negligent failure to act) 
committed by Seller, or (iv) an act for which strict liability will be inputted to 
seller, is limited to the “limited warranty” of  repair and/or replacement as so 
stated in our warranty of  product.  In no event shall the Seller be liable for 
any special, indirect, consequential or other damages of  a like general nature, 
including, without limitation, loss of  profits or production, or loss or expenses 
of  any nature incurred by the buyer or any third party.
UE specifications subject to change without notice.

Содержание Excela 1GSWLL














Отзывы: