Unitech MS282 Скачать руководство пользователя страница 50

Страница: 50 / 169

- 33 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS282 User’s Manual

2.17 Low Light Scene Detection

Scan one of the following bar codes to allow the engine to detect motion in dim
to dark illumination environments when in presentation mode:

•

No Low Light Scene Detection

- The engine attempts to detect motion as

best it can with the aim pattern and
illumination turned off when the engine is
idle.

•

Aiming Pattern Low Light Assist Scene Detection

–

Illumination is off, but the aim pattern is on when the engine is idle to
assist in scene detection.

• Dim Illumination Low Light Assist Scene Detection

–

The aim pattern is off, but illumination is on at a dim level to assist in
scene detection.

No Low Light Assist Scene Detection*

Aiming Pattern Low Light Assist Scene Detection

Dim Illumination Low Light Assist Scene Detection

Содержание MS282


























































































































































Результаты поиска

Содержание MS282

Отзывы:

Похожие инструкции для MS282

Бренды по названию

Популярные бренды

Unitech MS282, Руководство пользователя

Результаты поиска

Содержание MS282

Отзывы:

Похожие инструкции для MS282

Бренды по названию

Популярные бренды