background image

TX3-CX-1NP Installation

1

LT-5997 Rev 3 January 2018

Subject to change without notice. See http://www.mircom.com for the latest information

TX3-CX-1NP Installation

These instructions explain how to install the TX3-CX-1NP and the TX3-P300-HA card reader

 

in the following TX3 units:

These units include 2 #6-32 x 1/2" screws for attaching the TX3-P300-HA card reader to the 
inside of the door.

A.

Contents of Kit

Qty 1... TX3-CX-1NP
Qty 2... Nuts for attaching TX3-CX-1NP to the TX3 unit
Qty 1... USB cable for programming TX3-CX-1NP
Qty 1... USB flash containing TX3 software and manuals

B.

Mount TX3-CX-1NP

1.  Mount TX3-CX-1NP on the two posts as shown in Figure 1.

2.  Secure it with the provided nuts.

Figure 1

Mount TX3-CX-1NP

C.

Mount the TX3-P300-HA Card Reader

Secure the card reader to the plastic bracket on the inside of the door with the 2 #6-32 x 1/2" 
screws that are included with the TX3 unit.

Note:

Do not use the cover that is included with the reader.

Note:

Install the reader with the LED facing out.

TX3-TOUCH-F15-B/C

TX3-200-8U-B/C

TX3-1000-8U-B/C

TX3-2000-8U-B/C

TX3-TOUCH-S15-B/C

TX3-200-8C-B/C

TX3-1000-8C-B/C

TX3-2000-8C-B/C

TX3-TOUCH-F22(-C)

TX3-TOUCH-S22(-C)

Nut

Nut

Card reader 
connections

RJ45 connector for 
Internet communication 
and Power over Ethernet 

DIP switches

Installing on a telephone entry unit

Installing on a Touch Screen

Содержание TX3-CX-1NP

Страница 1: ...anuals B Mount TX3 CX 1NP 1 Mount TX3 CX 1NP on the two posts as shown in Figure 1 2 Secure it with the provided nuts Figure 1 Mount TX3 CX 1NP C Mount the TX3 P300 HA Card Reader Secure the card reader to the plastic bracket on the inside of the door with the 2 6 32 x 1 2 screws that are included with the TX3 unit Note Do not use the cover that is included with the reader Note Install the reader ...

Страница 2: ... an IP address from the DCHP server Set DIP switch 8 on to set a fixed IP address using the TX3 Configurator software For more information and the complete list of RS 485 addresses see LT 980 the TX3 Card Access System Manual on the Mircom website www mircom com or the USB flash E Connect the Card Reader Card reader requirements Card readers must meet the following minimum requirements in order to...

Страница 3: ...2 Request to Exit built in reader 22 AWG INPUT 1 Door contact built in reader 22 AWG LED R RJ45 connector for Internet communication Power can be provided through Power over Ethernet if not provided by the DC power terminals Micro USB port Connect to computer for network firmware upgrade and configuration maximum length of USB cable 8 feet 2 4 m 12 VDC 15 W Input power 18 AWG 24 48 VDC 15 W Input ...

Страница 4: ...SB flash Outputs For details on programming the outputs see LT 995 on the Mircom website www mircom com or the USB flash G Connect the Power The Single Door Controller can be powered in three ways Power over Ethernet PoE 12 VDC 15 W 24 57 VDC 15 W H Card Reader Beeper The beeper indicates specific events at different beep rates as follows Card Presented One short beep Access Granted Two short beep...

Отзывы: