Unitech MS282 Скачать руководство пользователя страница 122

Страница: 122 / 169

- 105 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS282 User’s Manual

3.14.7 GS1 DataBar Expanded Security Level

The engine offers four levels of decode security for GS1 DataBar Expanded
bar codes.

•

Security Level 0

- The engine operates in its most aggressive state, while

providing sufficient security decoding most in-spec bar
codes.

•

Security Level 1

- This setting eliminates most misdecodes while

maintaining reasonable aggressiveness.

•

Security Level 2

- Select this option with greater bar code security

requirements if Security Level 1 fails to eliminate
misdecodes.

•

Security Level 3

- If you selected Security Level 2 and misdecodes still

occur, select this security level to apply the highest
safety requirements.

GS1 DataBar Expanded Security Level 0

GS1 DataBar Expanded Security Level 1*

GS1 DataBar Expanded Security Level 2

GS1 DataBar Expanded Security Level 3

Содержание MS282


























































































































































Результаты поиска

Содержание MS282

Отзывы:

Похожие инструкции для MS282

Бренды по названию

Популярные бренды

Unitech MS282, Руководство пользователя

Результаты поиска

Содержание MS282

Отзывы:

Похожие инструкции для MS282

Бренды по названию

Популярные бренды