Gigarouter
UF72N User Manual
Page 184 of 203
to notify the user there is still a call on hold.
►
(#)Quick Dial Key:
Whether to send telephone number immediately after receiving the # key.
►
Asterisk Func Key:
Whether to use the ‘*’ key as flash key.
►
Tap Report:
Whether to report an event to server when flash detected.
►
Escape Seq:
Whether to use an escape characters when sending special DTMF.
►
CID Enable:
Whether to enable caller id globally.
►
Callee Inverse Polarity:
Whether to activate the Polarity Reversal for FXS callee.
►
Caller Inverse Polarity:
Whether to activate the Polarity Reversal for FXS caller.
►
Call Forwarding Unconditional:
Enable or disable CFU function, if enabled, enter
Call Number
.
1) Set by keypad service system:
*57*TN#
, TN is the phone
number to be redirected to.
2) Cancel by keypad service system:
#57#
.
►
Call Forwarding No Reply:
Enable or disable CFNR, if enabled, enter
Call Number
and
Wait
Time Long
.
1) Set by keypad service system:
*41*TN#
, TN is the phone
number to be redirected to.
2) Cancel by keypad service system:
#41#
.
►
Call Forwarding On Busy:
Enable or disable CFB function, if enabled, enter
Call Number
.
1) Set by keypad service system:
*40*TN#
, TN is the phone
number to be redirected to.
2) Cancel by keypad service system:
#40#
.
►
Hotline Number:
Enter number to hotline function, empty expressed disable.
1) Set
delay hotline
number by Keypad service system:
*52*TN#
,
TN is the hotline number.
2) Cancel
delay hotline
number by Keypad service system:
#52#
.
3) Set
instant hotline
number by Keypad service system:
*42*TN#
, TN is the hotline number.
4) Cancel
instant hotline
number by Keypad service system:
#42*EN#
, instant hotline can only be deactivated with other
extension; EN is the extension number which needs to deactivate
instant hotline.
►
Delay Time:
Time 0 indicates immediate Hotline, Otherwise, indicates delay
Hotline. The Delay Time must be configured on the WEB.
►
CID Restriction:
Enable or disable CID Restriction. If
Anonymous As UserName
is
chosen, user name content is Anonymous also.
►
Enable No Disturb:
Allows block incoming calls at any time.
►
Enable Call Waiting:
When you talking, a third party phone comes in, you can hear the
beep tone.
►
Enable MWI:
Enable or disable MWI (Message-waiting indicator) function.
►
Enable CID:
Enable or disable to send CID to phone.
►
CID Mode:
There are two methods used for sending caller ID information
depending on the application and country specific requirements:
FSK
:
caller ID generation using Frequency Shift Keying (FSK)
DTMF:
caller ID generation using DTMF signaling.
The command “show abbr-dial” shows the abbreviated number of the user as below:
Содержание UNIFIBER GIGAROUTER UF72N
