UNIBLOC PD600 Скачать руководство пользователя страница 8

Страница: 8 / 55

8 UNIBLOC-PD Operation & Service Manual: PD600-677

unless it is assembled with a flushed shaft seal that is properly installed with a fully operational flushing system.

Installation of pressure gauges/sensors in conjunction with the pump’s suction and discharge connec

tions is recommended to be able to monitor the pumps pressure.

When cleaning manually or by CIP, SIP methods, the operator must

ensure that a suitable procedure is used in accordance with the systems

requirements.

If operating with a pulley, proper support must be selected to prevent

excessive bearing wear and bending of the shaft. See fig. 2.5. Additional

safety guards are a must.

3.0 Installation

3.1 Handling and Storage

Caution must be taken when lifting the pump or pump unit. For all parts over 20kg (44lbs) we recommend the

use of a lifting device or lifting arrangement when unpacking or moving. Check the weight guide in section 6.0

for details. See fig. 3.1 and 3.2 for lifting guidance. For large pumps, lifting eyes will be supplied with the pump

to assist in lifting/moving.

When you receive your product please follow these steps:

•

Check packaging for any damage in transit

•

Check the packing slip against received goods

•

If an assembly, make sure the manual for the drive unit is included

•

Visually inspect the product for any signs of damage

•

Report any damage immediately to the carrier

If installation of the pump is delayed, store and protect the unit properly by:

•

Not removing plastic port protectors.

•

Selecting a clean, dry storage location free from vibration. In a moist or dusty atmosphere, further protect the

pump/assembly with suitable cover.

fig. 2.5

Vertical Port Mounting

Horizontal Port Mounting

fig. 3.1

Horizontal Port Mounting

Vertical Port Mounting

fig. 3.2

Содержание PD600
























































Результаты поиска

Содержание PD600

Отзывы:

UNIBLOC PD600, Руководство по эксплуатации и обслуживанию, Страница: 8 / 55

Результаты поиска

Содержание PD600

Отзывы: