UNIBLOC PD600 Скачать руководство пользователя страница 12

Страница: 12 / 55

12 UNIBLOC-PD Operation & Service Manual: PD600-677

4.0 Maintenance

BEFORE ANY MAINTENANCE TAKES PLACE: TURN OFF POWER SUPPLY TO THE MOTOR.

4.1 Clean In Place, CIP

The pump can be manually cleaned or by Cleaned In Place (CIP). The following is an example of suggested CIP pro

cedure. However, specific advice for each application can be obtained from your pump supplier.

If the temperature difference between the process liquid, or the pump, and the cleaning media is greater than 10º C

(18º F), stop the pump and then introduce the cleaning liquid. If the liquid is not gravity fed and the pump must draw

the liquid from a supply vessel, run the pump until it is filled and then stop. Allow the pump to adjust to the cleaning

liquid temperature and then continue running the pump at normal speed. If the pump has double mechanical seals,

they must be continued to be flushed during the CIP process. The length of time necessary to clean the pump and the

type of liquid used is dependent on the type of process liquid and its characteristics.

Never touch the pump or the pipelines as they can be extremely hot.

Always use rubber gloves and protective goggles if handling caustic substances.

The rotors and shaft seals in the pump have been selected for specific temperature and pressure

conditions. Verify with Unibloc-Pump or the documentation supplied with the pump that the operating

parameters are not exceeded.

Always rinse well with clean water after using cleaning agent.

4.2 Steam In Place, SIP

The pump can be manually cleaned or cleaned with Steam In Place (SIP). Following is an example of suggested SIP

procedure. However, specific advice for each application can be obtained from your pump supplier.

Stop the pump and introduce steam into the system. If the pump must be operated, allow it to adjust to the steam

temperature and then run it between 50-100 rpm. If the pump has double mechanical seals, they must continue to be

flushed during the SIP process. The length of time necessary to steam the pump is dependent on the type of process

liquid used and its characteristics. After the SIP process is complete, allow the pump to return to ambient temperature

or to the temperature of the process liquid. Resume normal operation to remove condensate or to begin pumping

another media.

Never touch the pump or the pipelines as they can be extremely hot.

Always use rubber gloves and protective goggles if handling caustic substances.

The rotors and shaft seals in the pump have been selected for specific temperature and pressure

conditions. Verify with Unibloc-Pump or the documentation supplied with the pump that the operating

parameters are not exceeded.

Always rinse well with clean water after using cleaning agent.

Содержание PD600
























































Результаты поиска

Содержание PD600

Отзывы:

UNIBLOC PD600, Руководство по эксплуатации и обслуживанию, Страница: 12 / 55

Результаты поиска

Содержание PD600

Отзывы: