UNIBLOC PD600 Скачать руководство пользователя страница 23

Страница: 23 / 55

UNIBLOC-PD Operation & Service Manual: PD600-677 23

ROTORS

ROTOR HOUSING

SHAFTS

BEARING HOUSING

SEAL CARTRIDGE O-RINGS (OUTER)

SEAL CARTRIDGE

SEAL CARTRIDGE O-RINGS (INNER)

WEAR SLEEVES

WEAR SLEEVE O-RINGS

RETAINING RING BOLTS

(4 or 8 Bolts Per Seal)

RETAINING RINGS

REAR VEW- ROTOR HOUSING

FRONT VEW- ROTOR & BEARING HOUSING

REAR ROTOR HOUSING STUD NUTS

fig. 4.11

SEAL REMOVAL TOOL

(P.N. 6011)

SHOULDER SCREWS

SEAL FLUSH HOUSING

1. Insert shoulder screws into key slots

on Seal Cartridge

2. Ensure that the removal tool is

engaged with Seal Cartridge by slightly

twisting tool in clockwise direction

Double O-ring Seal Removal with Seal Removal Tool

3. Remove Seal Cartridge by pulling

tool away from pump.

fig. 4.12

4.4.5.3.1 Double O-Ring Seal Removal- MODELS: PD602, PD652, PD677

(reference figs. 4.1, 4.11, 4.12)

Slide the

Rotors

off the

Shafts

. If the rotors will not slide off they can be removed simultaneously with the

Rotor

Housing

. Unless they are being replaced,

DO NOT USE PLIERS OR CHANNEL LOCKS TO REMOVE THE RO-

TORS. THEY WILL BE DAMAGED.

Pry the

Seal Cartridges

from rear of

Rotor Housing.

Alternatly, the

Seal

Cartridges

can be removed with the use of the Double O-ring Seal removal tool

6011

(see fig. 4.12 and section

6.3.2). The

Wear Sleeves

may come out with the

Seal Cartridges

. If so, remove the

Wear Sleeves

from the

Seal

Cartridges

and remove the

Seal Cartridge O-rings

(inner & outer). Remove

Wear Sleeves

from shafts if they did not

come out with the

Seal Cartridges

. Once off the

Shafts

, remove the

Wear Sleeve O-rings

. If servicing the

Bearing

Housing

, remove the

Rotor Housing

by first disconnecting the flushing system, if applicable, and loosening the

Rear

Rotor Housing Stud Nuts

. Use a hoist and eye bolt to support the

Rotor Housing

. Tap on the ports with a rubber

mallet and pull the

Rotor Housing

off. The

Retaining Rings

do not have to be removed to service the seal.

Содержание PD600
























































Результаты поиска

Содержание PD600

Отзывы:

UNIBLOC PD600, Руководство по эксплуатации и обслуживанию, Страница: 23 / 55

Результаты поиска

Содержание PD600

Отзывы: