UNIBLOC PD600 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 55

UNIBLOC PD600 Скачать руководство пользователя страница 38

38 UNIBLOC-PD Operation & Service Manual: PD600-677

1

2

3

8

11

12

4

5

6

9

10

7

*

HIGH PRESSURE (HP) CONFIGURATION

--- CONTACT UNIBLOC-PUMP FOR PART NUMBER

SHAFT SEALS ARE NOT SHOWN ON THIS DRAWING. PLEASE REFER TO INDIVIDUAL SEAL DRAWINGS FOR SEAL INFORMATION.

STAINLESS STEEL ROTOR VARIATIONS

M12 WING NUT

4433

8/12*

FRONT COVER

3240A/3240B*

1

FRONT COVER O-RING

4240

1

M12 X 35 SOCKET HEAD CAP SCREW

M12 X 35

6

O-RING

4245

2

ROTOR BOLT WASHER

3390

2

STAINLESS STEEL ROTOR

---

2

STUD

---

8/12*

M14 X 40 DOWEL PIN

DPM14 X40-3

10

1

11

12

REV. NO.

ANGULAR 0.0° ± 0.1° 0.00° ± 0.05°

DECIMALS 0.0 ± 0.1 0.00 ± 0.05 0.000 ± 0.005

UNLESS OTHERWISE NOTED:

TOLERANCES

G801

600/650

(UNLESS NOTED ON DWG.)

FINISH

MATERIAL

WEIGHT

RELEASE DATE

SHEET 1 OF 2

DWG. NO.

SIZE

DWG. TITLE

PUMP HEAD ASSEMBLY

:

STAINLESS STEEL ROTORS

AUG. 18, 2015

ALL DIMENSIONS IN MM

DRAWN

CHECKED

APP'D

SCALE

DATE

BY

KL

08/18/15

0

THIS DRAWING AND ALL IDEAS INCORPORATED IN ITS DESIGN IS THE EXCLUSIVE PROPERTY OF UNIBLOC HYGIENIC TECHNOLOGIES, LLC. ITS ACCEPTANCE CONSTITUTES AN AGREEMENT THAT IT SHALL BE TREATED AS A CONFIDENTIAL DOCUMENT USED FOR NO OTHER PURPOSE THAN TO AID IN ITS CONSTRUCTION, THAT IT IS TO BE RETURNED UPON REQUEST, AND THAT IT IS NOT TO BE DISCLOSED OR COPIED EXCEPT AS AUTHORIZED IN WRITING BY UNIBLOC HYGIENIC TECHNOLOGIES, LLC.

«
...
36
37
38
39
40
...
»

Содержание PD600
























































Отзывы:

Нет отзывов