UNIBLOC PD600 Скачать руководство пользователя страница 55

Страница: 55 / 55

Patented Designs Shown

WARRANTY

Unibloc Hygienic Technologies, LLC (“Unibloc”) warrants that its product will be free from defects

in material and workmanship which results in noncompliance with the Specifications for such prod-

uct. This warranty shall begin upon delivery and continue for a period of one (1) year from such

date. If during this period the product does not comply with its specifications as a result of defects

in material or workmanship, contact Unibloc to arrange return of the faulty product, shipping

prepaid and fully insured, to an authorized Unibloc service facility. If upon inspection of the item in

question, defects in workmanship or materials are revealed, Unibloc’s sole obligation under this

warranty shall be to supply a repair or replacement for any defective part of a product, and to return

such product to the customer by shipping it EX WORKS (as defined in Incoterms 2020) the service

facility. Unibloc shall not be required to supply any labor for repairs or replacement of parts. This

warranty is void if the product has not been used as recommended or instructed, has been altered

or used with unauthorized accessories, has been subject to misuse, abuse or accident, or has

been damaged due to causes not related to poor workmanship or defective materials. All parts or

components not manufactured by Unibloc are warranted only to the extent of the warranty of the

respective manufacturers.

THIS LIMITED WARRANTY IS EXPRESSLY GIVEN IN LIEU OF ALL OTHER EXPRESS OR

IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANT-

ABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT, ALL OF

WHICH ARE HEREBY EXCLUDED. IN NO EVENT SHALL UNIBLOC OR ITS AFFILIATES BE

LIABLE TO ANYONE FOR SPECIAL, COLLATERAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, WHETHER ARISING IN CONTRACT OR IN TORT.

UNIBLOC RESERVES THE RIGHT TO MAKE TECHNICAL CHANGES WITHOUT NOTICE.

Unibloc Hygienic Technologies, LLC

1650 Airport Road NW, Suite 110

•

Kennesaw, Georgia 30144

•

USA

Tel

770-218-8900

E-Mail

[email protected]

www.unibloctech.com

Содержание PD600
























































Результаты поиска

Содержание PD600

Отзывы:

UNIBLOC PD600, Руководство по эксплуатации и обслуживанию, Страница: 55 / 55

Результаты поиска

Содержание PD600

Отзывы: