background image

 

01

 

 

0.

Introduction

 

 

0.1 

Before using the vacuum pump

 

 

Thank you for purchasing this product. Your custom is very much appreciated. 
This pump is only for vacuum pumping, and may malfunction or cause accidents if not 
handled appropriately. Please use instruction manuals after attention enough for 
check / maintenance / security sides after a reading well.

 

 
 

Personnel handling the equipment 

 

Only  persons  who  have  read  this  manual  thoroughly,  and  have  sufficient 

understanding of safety, pump specifications, and method of operation, can operate 

this pump. 

 
 

Read the manual thoroughly 

 

 

Please completely read a manual well to use this product definitely. Please read 

the section on “introduction in the security” “use for safe operation” by all 

means. 

 
 
Keep this manual in a safe place   

 

Keep the instruction manual carefully. After reading this manual, be sure to keep 

it in a safe place, which is readily accessible to others needing to use it. 

 
 

Copying this manual is prohibited    

 

This instruction manual can copy no part for sale without our permission. 

 
 
Statutory requirements for disposal    

 

Follow all statutory and local authority regulations when disposing of this pump. 

 
 
 

Содержание GHD-031A














































Отзывы: