background image

 

-23- 

(2)  Inspection of the amount of pump oil 

Please replenish it with a prescribed pump as the pump oil side is in the range 

of the red circle of the oil level gauge while driving. 

(3)  Inspection of oil leakage 

When oil leak was caused by drain plug seal region, the exchange of the part is 

necessary. Our specified O-rings and seals are always available from the service 

departments shown at the back of this manual. When necessary, contact them.  

(4)  Inspection of abnormal sounds and vibration 

        Check the nuts and bolts for looseness. 

(5)  Inspection of the oil mist trap 

When using the oil mist trap in replacement of the standard outlet port, pay 

attention to the clogging of the filter in the oil mist trap. 

If the clogging advances, evacuated gas cannot be exhausted any longer, which 

causes the oil gauge to protrude and oil leakage from the shaft seal section or 

drain plug seal section. The maximum internal pump pressure is 0.03 MPa (gauge 

pressure). 

When the pump is operated continuously for a long time or when the pump is extremely 

contaminated with evacuated gas, overhaul is required. Contact the nearest sales or service 

department among those listed at the back of this manual.

 

Содержание GHD-031A














































Отзывы: