background image

 
 

 

 

3.5  Piping 

1)  Install piping carefully to prevent leaks. 
2)  Piping connected to the inlet should be at least 6 mm inside diameter. 
3) Use rubber hoses, etc. to ensure that pump vibrations do not reach between the pump and 

piping, otherwise the pump or piping may be damaged. 

4)  Ensure that piping connected to the outlet does not cause back pressure. Maximum back 

pressure is 0.03 MPa (gauge pressure). 

5) In case of selecting the inlet pipe and exhaust pipe that are not from our products, please 

select the exhaust pipe that has same or larger inner diameter length with the inlet pipe. 

6) When starting the pump, it may not start if the intake-side pressure is lower than the 

  atmospheric pressure. 

Attach an atmospheric release leak valve between the pump intake pipe and vessel,   
and set the intake-side pressure to atmospheric pressure when starting the pump. 
After starting the pump, always close the leak valve. 

7)  When evacuating a vessel, ensure that a shut-off valve is placed between the pump inlet pipe 

and the vessel (see Fig.3.1). 

 

 

 

 

 

 

Fig.3.1 Example of Piping Used When Evacuating a Vessel 

 
 
3.6  Storage 
 

Turn the switch OFF (set to O), remove the power plug from the outlet, place the rubber caps 
over the inlet and outlet, and store the pump in an area of low humidity. 

 

4. Cautions for Operation 

4.1  Cautions for Operation 

 

 

See Danger (1)(2),P04 

 

See Warning (8),P04 

(15)(16)(17), P05 

 

See Caution (4)(5)(6)(7)(8), P05

 

 

See Note (3)(4)(5),P06 

(6)(7)(8)(9)(10)(11)(12), P07 

 
1)

 

To maintain the performance of the pump, always ensure that it is cleaned internally after use. 

 

 Clean by ingesting clean air for 3~5 minutes under no-load conditions. 

2)  Consult the manufacturer if the pump is to be used in a special application. 

 

4.2  Operation of the Thermal Protection Relay 

1)  When the thermal protection relay operates, switch the pump power supply OFF (set to O), 

remove the power cord from the outlet, and contact the manufacturer. Note that the pump will 
be very hot and should not be touched. 

 

Vacuum pump 

Filter 

Leak valve 

Shut-off valve  Vessel 

!

Caution

 

!

Note 

!

Warning

 

 

!

Danger 

Содержание DTC-22




























Отзывы: