ultracomfort Power Recline UC551-L Скачать руководство пользователя страница 18

Страница: 18 / 94

Spacer Bar Replacement

(See StellarComfort diagram on page 50.)

Tools needed:

Needle nose pliers, 7/16” wrench (qty.2)

This is what a spacer bar looks like.

The spacer bar is located at the rear of the chair across the top of the

seat. The back is attached to the ends of the spacer bar.

To replace the spacer bar, you will need to re-

move the back from the chair.

With the chair plugged in, use the hand control to

recline the back to make it easier to get to the

nuts you will need to remove.

Rear Mounting Bar

There are 3 nuts on each side of the back that you will

need to remove. Place a wrench on the head of each

bolt to hold it in place as you remove the nuts.

Содержание Power Recline UC551-L































































































Результаты поиска

Содержание Power Recline UC551-L

Отзывы:

Похожие инструкции для Power Recline UC551-L

Бренды по названию

Популярные бренды

ultracomfort Power Recline UC551-L, Руководство по обслуживанию

Результаты поиска

Содержание Power Recline UC551-L

Отзывы:

Похожие инструкции для Power Recline UC551-L

Бренды по названию

Популярные бренды