ultracomfort Power Recline UC551-L Скачать руководство пользователя страница 14

Страница: 14 / 94

22. Use the hitch pin(s), clevis pin(s), and washers to fasten the recline strap(s) to the recline bar.

23. Use the four (4) T30 lag screws, eight (8) on models (540M-26, 542M-26, 542-ME6, 550-M26)

to fasten the lift frame to the arm assembly.

24. Reinstall the hand control extension wire clamp.

25. Plug the transformer and hand control extension into the motor or control box.

26. Plug the transformer back into the wall outlet and test.

27. Reinstall the seatback if removed.

Recline Bar Replacement

Tools needed:

Needle nose pliers, P2 Phillips screwdriver, T30 screw bit, wire cutters, zip

ties, 3/8 inch socket, a stool or stand for placing the chair upside down.

Unplug the transformer from the wall outlet.

2. Reach down into the chair’s side pocket until you feel the disconnect latch on the hand control

extension.

3. Pull back on the disconnecting latch.

4. Put one hand on the back of the extension wire plug base and one on the hand control plug

base and pull the two pieces apart.

5. Gently push the chair over onto the footrest, turn it upside down or, gently push it over onto its

side, opposite of the hand control.

6. Remove the four (4) T30 lag screws, eight (8) on models (540M-26, 542M-26, 542-ME6,

550-M26) that hold the lift frame to the arm assembly.

7. Remove the hitch pin(s), clevis pin(s), and washers that fasten the recline strap(s) to the recline

bar.

8. Remove the hand control extension wire clamp.

9. Lift the lift frame out of the chair shell and place it off to the

side.

10. Use the 3/8 inch socket to remove the two (2) bolts that

fasten each scissor mechanism to the arm assembly.

While this next step can be done alone,

it does require extra attention. You must remove the

arm assembly without twisting the frame. Excessive

twisting will cause the board holding the arms together

to snap.

11. Stand behind the chair and pull the arms away from the

chair being careful not to get the material snagged in the

scissor mechanisms.

12. Place the arm assembly to the side.

13. Use the 1/2 inch socket to remove the bolts that fasten

the recline bar to the seat.

Note the position of the recline bar,

so you do not install the new bar in upside down.

14. Use the 1/2 inch socket to install the bolts that fasten the new recline bar to the seat.

15. Place the arm assembly in place so that the bolt holes in the scissor mechanisms line up with

the bolt holes in the armrest.

16. Install the two (2) bolts that fasten each scissor mechanisms to the arm assembly.

17. Make sure the footboard is completely closed.

Note: When installing the lift frame the footboard must be completely closed when you
fasten the lift frame to the armrest assembly or the footboard will not close properly.

Note:

Seat bar on StellarCom-

fort models only.

Seat bar

Bolt

Recline Bar

Seat

Содержание Power Recline UC551-L































































































Результаты поиска

Содержание Power Recline UC551-L

Отзывы:

Похожие инструкции для Power Recline UC551-L

Бренды по названию

Популярные бренды

ultracomfort Power Recline UC551-L, Руководство по обслуживанию

Результаты поиска

Содержание Power Recline UC551-L

Отзывы:

Похожие инструкции для Power Recline UC551-L

Бренды по названию

Популярные бренды