Ubiquiti airFiber 24, Руководство пользователя

Страница: 31 / 68

27
Chapter 4: Dashboard airFiber AF-24/AF-24HD User Guide
Ubiquiti Networks, Inc.
Device Status
The next section of the Dashboard displays additional
status information for the local device.
Operating Mode Displays the mode of the local airFiber
radio: Master , Slave , or Reset .
RF Link Status Displays the status of the airFiber AF-24:
RF Off , Syncing , Beaconing , Registering , Enabling , Listening ,
or Operational .
Version
Displays the version of the firmware running in
the local device.
Date Displays the current system date and time (the
format is browser and location-dependent). The system
date and time is retrieved from the internet using NTP
(Network Time Protocol). The NTP Client is disabled by
default on the
Services page. The device doesn’t have an
internal clock, and the date and time may be inaccurate if
the NTP Client is disabled or the device isn’t connected to
the internet.
Radio Mode Always displays MIMO (SISO mode is not
supported).
Duplex Displays Full Duplex or Half Duplex. Full duplex
mode allows communication in both directions
simultaneously.
Half duplex mode allows communication
in one direction at a time, alternating between
transmission and reception.
Uptime This is the total time the device has been running
since the latest reboot (when the device was powered up)
or software upgrade. The time is displayed in days, hours,
minutes, and seconds.
Link Uptime
Displays the total time the airFiber link has
been continuously operational. The time is displayed in
days, hours, minutes, and seconds.
Regulatory Domain Displays the regulatory domain
( FCC/ICC , ETSI , or Other ), as determined by country
selection.
Security AES-128 is enabled at all times.
Duty Cycle Displays the duty cycle.
Latitude/Longitude Based on GPS tracking, reports the
local device’s current latitude and longitude. Clicking
the link opens the reported latitude and longitude in a
browser using Google Maps
™
( http://maps.google.com ).
Altitude
Based on GPS tracking, reports the local device’s
current altitude relative to sea level.
Synchronization airFiber uses GPS to synchronize the
timing of its transmissions. By default, this option is
Disabled .
Satellites Tracked Displays the number of satellites
tracked by the GPS receiver.
GPS Signal Quality Displays Global Positioning System
(GPS) signal quality as a percentage value on a scale of
0-100%.
Conducted TX Power
Displays the conducted transmit
power out of the radio before any antenna gain.
RX Gain Displays the gain for the RX antenna of the local
AF-24 device: High or Low .
Remote RX Gain Displays the gain for the RX antenna of
the remote AF-24 device: High or Low .
Ethernet Connection Status
Mgmt MAC Displays the MAC address of the Config port.
Mgmt Displays the speed and duplex of the Config port.
Data Displays the speed and duplex of the Data port.
Data Cable Length Displays the length of the Ethernet
data cable attached to the local radio. This is displayed
only for cables longer than 20 m.
Data Pair 0 (Pins 1, 2)
If the cable is functioning properly,
this field displays the SNR of the twisted pair. If the cable
has a fault, the field displays the fault (
Open or Short ) and
the distance at which the fault has occurred. If the remote
port is administratively shut down,
Normal is displayed .
Data Pair 1 (Pins 3, 6) If the cable is functioning properly,
this field displays the SNR of the twisted pair. If the cable
has a fault, the field displays the fault (
Open or Short ) and
the distance at which the fault has occurred. If the remote
port is administratively shut down,
Normal is displayed .
Data Pair 2 (Pins 4, 5) If the cable is functioning properly,
this field displays the SNR of the twisted pair. If the cable
has a fault, the field displays the fault (
Open or Short ) and
the distance at which the fault has occurred. If the remote
port is administratively shut down,
Normal is displayed .
Data Pair 3 (Pins 7, 8) If the cable is functioning properly,
this field displays the SNR of the twisted pair. If the cable
has a fault, the field displays the fault (
Open or Short ) and
the distance at which the fault has occurred. If the remote
port is administratively shut down,
Normal is displayed .