U.S. Boiler Company ALTA ALTAC-136B Скачать руководство пользователя | Manualshive

Страница: 1 / 104

background image

110327-07 - 2/23

ALTA

• Combi Boiler/Water Heater

• Condensing

• Direct Vent

• Gas Fired

Models:
• ALTAC-136
• ALTAC-136B
• ALTAC-200

WARNING

This boiler must only be installed, serviced, or repaired by a qualified installer, service agency or gas supplier.

Improper installation, adjustment, alteration, service or maintenance can cause severe personal injury, death,

or substantial property damage. For assistance or additional information, consult a qualified installer, service

agency, or the gas supplier. Read these instructions carefully before installing.

!

Installation, Operating and Service Instructions for

Manual Contents   Page
1.  Installer Read Before Proceeding  . . . . . . . . . . .3
2. Homeowner Read Before Proceeding . . . . . . . .4
3. Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4.   How It Works  . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5.   Locating Boiler  . . . . . . . . . . . . . . . . . . . . . . . . .10
6.   Preparing Boiler  . . . . . . . . . . . . . . . . . . . . . . . .14
7.   General Venting  . . . . . . . . . . . . . . . . . . . . . . . . .17
8.    Sidewall Direct Venting . . . . . . . . . . . . . . . . . . .24
9.   Vertical Direct Venting   . . . . . . . . . . . . . . . . . . .30
10.  Heating System Piping  . . . . . . . . . . . . . . . . . . .36
11.  Domestic Water Piping  . . . . . . . . . . . . . . . . . . .39
12.  Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
13.  Field Wiring   . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
14.  Condensate Disposal  . . . . . . . . . . . . . . . . . . . .47
15.  Start-up and Checkout    . . . . . . . . . . . . . . . . . .48
16.  Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
17.   Before Leaving Jobsite   . . . . . . . . . . . . . . . . . .67
18.  Service and Maintenance  . . . . . . . . . . . . . . . . .68
19.  Troubleshooting   . . . . . . . . . . . . . . . . . . . . . . . .73
20.  Internal Wiring Diagrams   . . . . . . . . . . . . . . . . .89
21.   Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Appendix
  A. Combination Refrigeration/Heating System  . .98
B. Water Quality and Boiler Additives  . . . . . . . . .99
C. Special Requirements In Massachusetts  . . .100
D. Code Required Text  . . . . . . . . . . . . . . . . . . . . .102

TO THE INSTALLER:

Affix these instructions adjacent to boiler.

Provide model number and serial number when
seeking information and support.

TO THE HOMEOWNER:

Retain these instructions for future reference.

Contact heating installer or technician for all issues

and support.

Version en Español disponible en el web del fabricante.

www.usboiler.net

1
2
3
...
»

Содержание ALTA ALTAC-136B









































































































Отзывы:

Нет отзывов

Похожие инструкции для ALTA ALTAC-136B

Бренд: DAXOM Страницы: 45

Бренд: IBC Страницы: 84

Бренд: Atlas Страницы: 48

Бренд: Viessmann Страницы: 36

Бренд: Biasi Страницы: 84

Бренд: Riello Страницы: 28

Бренд: Vaillant Страницы: 80

ARCEUS 12 kW MT

Бренд: E.C.A. Страницы: 38

ecoMAX pro 18 E

Бренд: Vaillant Страницы: 36

CITY CLASS 20 F

Бренд: Italtherm Страницы: 32

Бренд: Fondital Страницы: 80

Бренд: IDEAL Страницы: 52

Бренд: Unical Страницы: 48

Бренд: Ariston Страницы: 88

AAA Outdoor Boiler

Бренд: Nature's Comfort Страницы: 24

Бренд: Nature's Comfort Страницы: 25

Бренд: Ferroli Страницы: 120

Бренд: Chaffoteaux & Maury Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды