background image

U-Line Door Panel Installationl

10

9 Door Panel Installation

Custom 1/4'' Thick Door Panel Insert

Door Panel Preparation

A custom door panel may be inserted into the doorframe. Custom 
door panels can be flat or raised, as long as the maximum panel 
thickness, where inserted into the door reveal (channel), is no 
more than 1/4" thick. For raised panels, the depth of the reveal is 
1/4" on all four sides.

IMPORTANT

IMPORTANT

Raised panels will reduce the door’s 90° swing/zero 
clearance if the unit is installed next to a wall or similar 
type of structure.

Panel Dimensions.

The door panel must not weigh more than 20 lbs.

Door Panel Installation

Install the insert as follows:

CAUTION

Use care when handling the insert. Insert edges may be 
sharp.

1. Remove top hinge screw pin with 

Phillips head screwdriver. Remove 
door by tilting forward and lifting off 
bottom hinge pin.

2. Pull door gasket out of groove (top 

edge of door only). Start in the middle 
and pull outward, moving toward the 
edge . This may take some force.

Model

Width

Height

CLRCO2175

23 1/32”

27 11/16”

CLR2160

14 1/32”

27 11/16”

CO1175

22 15/16”

26 15/16”

CO29

19 13/16”

21 13/32”

CO2175

23 1/32”

27 11/16”

3. Remove the two outside screws holding 

door handle. Slightly separate door 
handle from door.

4. Pull handle up and off.

5. Slide custom door panel insert into 1/4-

inch channel in door front.

IMPORTANT

IMPORTANT

Use care not to damage magnet, located on door bottom, 
when installing door insert. Do not set door on bottom 
edge when pushing insert into place.

6. Holding door gasket out of the way, replace handle on door, 

making sure it is seated properly on insert and that screw holes 
line up.

7. Install two small screws removed in 

Step 3

.

8. Starting at the corners and working inward, push door gasket 

into place on door.

9. Place door on bottom hinge pin and install upper hinge screw.

Содержание CLR2160




















Отзывы: