Tuchel PLUS 560 Скачать руководство пользователя страница 31

Страница: 31 / 102

Coupling and uncoupling the sweeper

4-25

4.2.1

Three-point linkage - "front mounting"

•

The safety regulations from chapter 4.2 apply.

•

Undertake work on the sweeper only with engine switched off and after
depressurising the hydraulics. Remove the ignition key, secure carrier
vehicle against inadvertent starting up or rolling.

•

Check three-point hitch for contamination and clean if necessary.

•

Move carrier vehicle up to 300 mm

distance to the Sweeper PLUS 560

•

Insert pin diameter (1) or (2)

according to the trailer load

category of the vehicle
manufacturer and secure with

spring cotter pin (3).

➔

Fit upper link and secure

according to the

manufacturer’s instructions.

The adjustment of the

upper link must be

undertaken so that the

sweeper attachment unit is

vertical to the ground.

Fig. 4.2

•

Pull out cotter pin (4) and locking

bolt (5), then pull the parking stand

(6) upwards and secure it again via

the bottom hole.

•

Connect hydraulic hoses according

to the instructions of the vehicle

manufacturer.

•

Connect electrical cables for water-

spray system or lighting to the

switch box inside the carrier

vehicle.

•

Raise sweeper and carry out a

function test.

Fig. 4.3

Содержание PLUS 560







































































































Результаты поиска

Содержание PLUS 560

Отзывы:

Похожие инструкции для PLUS 560

Бренды по названию

Популярные бренды

Tuchel PLUS 560, Руководство по эксплуатации

Результаты поиска

Содержание PLUS 560

Отзывы:

Похожие инструкции для PLUS 560

Бренды по названию

Популярные бренды