manualshive.com logo in svg

Tuchel PLUS 560, Руководство по эксплуатации


Поделиться
Скачать
background image

Product description 

 

3-20

 

 

 

 

3.1.1 

Description of product and accessories 

 

 

•

  The Sweeper PLUS 560 permits dirt collection as well as simple sweeping 

operations. The simple sweeping operation can be carried out without having to 
disassemble the dirt hopper.

 

•

  The chassis consists of a robust, distortion-free welded structure.

 

•

  The main cylinder brush is freely suspended in the frame with a lever system. The 

brush setting is adjusted by means of a spacing bar. By pushing the spacer lever 
(leverage effect) the main cylinder brush can be adjusted as required ensuring

 

a consistently good sweeping result. 

•

  A powerful external hydraulic motor with a impact protection directly drives the main 

cylinder brush. The speed of rotation of the main cylinder brush depends on the oil 
flow and the operating equipment of the carrier vehicle.

 

•

  The main cylinder brush is provided as standard with 100% PP-Beeline brush rings. 

The brush ring diameter is 590 mm.

 

•

  The opening and closing of the dirt hopper is carried out by operating a hydraulic 

cylinder. The controls are operated from the carrier vehicle. A wear-resistant PU- 
sealing strip is attached along the whole length of the lower edge of the dirt hopper 
so as to guide the hopper edge evenly and without damage.

 

•

  The Sweeper PLUS 560 is appropriately equipped for the different kinds of carrier 

vehicles, via a direct attachment system. The relevant version allows attachment 
via three-point linkage, an A-frame or onto municipal vehicles, farm loaders as well 
as wheeled loaders.

 

•

   Pendicular compensation ensures level balance in operation, even on rough, 

uneven ground.

 

•

 

With the aid of the mechanical or (optionally hydraulic) slant adjustment it is 
possible to swing the Sweeper PLUS 560 20° to the right or the left.

 

 

3.2 

Add-on parts 

 

•

 

Water-spray system:

 

For dust binding with 100 or 200 litre water tank and 12 V (24 V) glanded pump. 

•

 

Hydr. lateral adjustment:

 

Angled positioning of Sweeper PLUS 560 by means of hydraulic cylinders. A double-acting 
hydraulic control circuit is required on the carrier vehicle. 

•

 

Hydr. side brush

 

Sweeping close to the edge, with control of rotation speed. 

•

 

Road traffic equipment

:

 

Consisting of warning flags and/or side-marker lights. Both are prescribed and to be used in 
public road traffic according to the regulations of the StVZO.( German Road Traffic Authority) 

•

 

Dirt hopper:

 

Hydraulic emptying by means of a hydraulic cylinder with shut-off valve for simple sweeping 
mode (without removing the dirt hopper). 

Содержание PLUS 560







































































































Отзывы:

Нет отзывов

Похожие инструкции для PLUS 560

MADVAC PS300 Operator'S Manual preview
PS300
Бренд: MADVAC Страницы: 182
Murray 6210701X54N Instruction Book preview
6210701X54N
Бренд: Murray Страницы: 206
Yardworks 31AM63KE515 Operator'S Manual preview
31AM63KE515
Бренд: Yardworks Страницы: 56
MTD 190-491 Owner'S Manual preview
190-491
Бренд: MTD Страницы: 25
Ariens Sno-Thro 932001 Owner'S Manual preview
Sno-Thro 932001
Бренд: Ariens Страницы: 12
KitchenAid KPEC992M Installation Instructions And Use And Care Manual preview
KPEC992M
Бренд: KitchenAid Страницы: 20
Craftsman 113.171500 Owner'S Manual preview
113.171500
Бренд: Craftsman Страницы: 16
DeWalt Pro Landscaping DCM587 Original Instructions Manual preview
Pro Landscaping DCM587
Бренд: DeWalt Страницы: 136
Stanley SPT500 Original Instructions Manual preview
SPT500
Бренд: Stanley Страницы: 20
Troy-Bilt 295 Operator'S Manual preview
295
Бренд: Troy-Bilt Страницы: 11
MTD E6C3H Operator'S Manual preview
E6C3H
Бренд: MTD Страницы: 28
Worx WG519 Manual preview
WG519
Бренд: Worx Страницы: 20
Worx WG500E Safety And Operating Manual preview
WG500E
Бренд: Worx Страницы: 12
Texas Combi 650 Instruction Manual preview
Combi 650
Бренд: Texas Страницы: 25
Texas 90062073 Original Instructions Manual preview
90062073
Бренд: Texas Страницы: 45
Texas 90062051 Manual preview
90062051
Бренд: Texas Страницы: 63
Texas 7011BE Instruction Manual preview
7011BE
Бренд: Texas Страницы: 64
Alto Sweeper Operator'S Manual preview
Sweeper
Бренд: Alto Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды