TSI Incorporated PORTACOUNT PRO+ 8038 Скачать руководство пользователя страница 80

Страница: 80 / 107

Chapter 7

Symptom

Possible Causes

Solution

Particle count is
zero or near zero

Alcohol level is low.

Replenish alcohol.

Sampling through HEPA
Filter.

Remove filter.

Twin Tube Assembly is
blocked.

Remove the blockage.

Moisture build-up in
Alcohol Wick.

Change Alcohol Wick
inside Alcohol Cartridge.
Run 2 hours to dry optics
(remove the alcohol
cartridge and install
storage cap).

Inferior or contaminated
alcohol.

Change Alcohol Wick
inside the Alcohol
Cartridge. Use only
approved alcohol.

PortaCount Pro

fit tester

is flooded with alcohol.

Run 2 hours to dry optics
(remove Alcohol Cartridge
and install Storage Cap).

Filter cover leaking.

Replace cover and O-ring.

Plugged nozzle.

See

Nozzle Cleaning

Service and Maintenance
chapter.

Requires frequent
refill of alcohol
(every hour or
less)

Moisture build-up inside
Alcohol Wick.

Change Alcohol Wick
inside cartridge. Run 2
hours to dry optics
(remove the alcohol
cartridge and install
storage cap) Use only
approved alcohol.

Alcohol visible in
Twin Tube
Assembly or
coming out of
Exhaust Port

PortaCount Pro fit tester
is flooded with alcohol.

Run overnight to dry
optics (remove Alcohol
Cartridge and install
storage cap).

Содержание PORTACOUNT PRO+ 8038












































































































Результаты поиска

Содержание PORTACOUNT PRO+ 8038

Отзывы:

Бренды по названию

Популярные бренды

TSI Incorporated PORTACOUNT PRO+ 8038, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PORTACOUNT PRO+ 8038

Отзывы:

Бренды по названию

Популярные бренды