background image

............ www.truemfg.com ............

True Food Service Equipment, Inc.

12

12

INSTALLATION / OPERATION INSTRUCTIONS

A.  

The compressor is ready to operate. Plug in the cooler.

B.  

Temperature control set at No. 4 position gives 

refrigerators an approximate temperature of 35°F. Allow 

unit to function several hours, completely cooling cabinet 

before changing the control setting.

C.  

Excessive tampering with the control could lead to service 

difficulties. Should it ever become necessary to replace 

temperature control, be sure it is ordered from your 

TRUE dealer or recommended service agent. 

D.  

Good air flow in your TRUE unit is critical. Be careful 

to load product so that it neither presses against the back 

wall, nor comes within four inches of the evaporator 

housing. Refrigerated air off the coil must circulate down 

the back wall.

NOTE 

If the cooler is disconnected or shut off, wait five minutes before 

starting again.

 

RECOMMENDATION 

Before loading product we recommend you run your TRUE unit 

empty for two to three days. This allows you to be sure electrical 

wiring and installation are correct and no shipping damage 

has occurred. Remember, our factory warranty does not cover 

product loss!

REPLACEMENT PARTS 

TRUE maintains a record of the cabinet serial number for your 

cooler. If at any time during the life of your cooler, a part is 

needed, you may obtain this part by furnishing the model number 

and serial number to the company from whom you purchased 

the cooler. Call Toll-Free: (800)-424-TRUE (Direct to Parts 

Department). (800)-325-6152 (U.S.A. & Canada only) or call: 

(636)-240-2400.

STARTUP

When installing unit, loading product or rearranging shelving, 

the slide doors must be propped open with the door latch. 

The door latch is located on the inside wall of the unit. (See 

image 1). 

If the door must be removed open it to full extension and 

then lift the door latch. Then lift the door up and out of the 

bottom track and then out of the top door frame. (See image 

2). Unhook the door cord from the top of the door. (See 

image 3). Set the door to the side with the bottom rollers 

facing up. Never set the slide door on it’s rollers. Resting door 

on rollers can cause damage and the door will not operate 

correctly when opening and closing. To reinstall door do the 

steps in reverse order.

SLIDE DOOR OPERATION

1

2

3

Содержание GDM-23




































Отзывы: