background image

............ www.truemfg.com ............

True Food Service Equipment, Inc.

9

9

INSTALLATION / OPERATION INSTRUCTIONS

STEP 2

 

Using a 7/16” wrench or adjustable wrench and 

1/8” allen wrench loosen roller and move 

along slotted hole. After adjustment has been 

made tighten the 

roller into place. 
See image 10.

TO ADJUST SLIDE DOOR

P-Clip keeps cord 

in-place (prevents 

cord damage).

Image 6 (Three Door Units ONLY)

STEP 6

Remove door cord from roller bracket. The black 

plastic tab holding the door cord slides out the 

back. See images 7 & 8.

STEP 1

 

After cabinet is installed in a final location and 

correctly leveled check for any openings when the 

slide doors are completely closed. If there are 

any gaps/openings between the closed doors 

and cabinet, the doors will need to be 

adjusted.

STEP 7

 

Let the door cord slowly retract back into the 

door side channel. The knot tied at the end of 

the door cord will keep the cord from retracting 

all the way back into the door channel. See 

image 9.

(Three Door Units ONLY)

STEP 1

 

Before removing slide door do not use the side 

latch. Tension on the door cord is needed to 

execute these operation instructions. Doors can 

not be removed unless placed in specific locations 

stated in these instructions.

STEP 2

Two Door Units:

 Slide the front door so it is 

centered on the cabinet. The door can not be 

removed unless it is centered. See image 1 for 

door channel openings and image 2 for 

centering door.

Three Door Units:

 Slide the middle door to 

the right side so the glass is centered with the left 

edge of the right side door. See image 3.

(Two Door Units ONLY)

 (Two Door Units ONLY)

CENTERED DOOR

(Three Door Units ONLY)

TRUE Logo

STEP 5

Slide left door to the right so right edge lines up 

with the end of the TRUE Logo located at the 

top of the door frame. See image 6. Then lift 

door out of track same way as image 4.

STEP 4

Slide right door to the left so left edge lines up 

with the left edge of TRUE Logo located above the 

door. See image 5. Then lift door out of track 

same way as image 4.

STEP 3

After centering the door lift it up and tilt top of 

door towards the back of the unit so the rollers are 

out of the top channel. Swing the bottom of the 

door out of the bottom channel. Then remove the 

door and set it down. See image 4.

(TWO DOOR UNITS SKIP TO STEP 6)

TRUE Logo

Gasket fasten to door bottom assures door will 

remain in track when unit is placed on uneven 

surface.

Door Cord

Knot

SLIDE DOORS

CENTER DOOR

1

2

3

4

5

6

7

8

9

10

Содержание GDM-23




































Отзывы: