background image

15

INSTALLATION - FITTING THE SHOWER TO THE WALL

Fig.11

•  If installing a feed pipe from the rear or 

bottom, the centre of the inlet valve to the 
wall surface is 21mm 

(fig.11)

.

• 

After choosing the site for the shower, use the 
backplate as a template to mark the fixing 
holes. 

•  The location of the fixing holes in the 

backplate are shown in 

(fig.12)

•  Drill and plug the wall. An appropriate 

drill bit should be used. If the wall is brick, 
plasterboard or a soft building block, appropriate 
wall plugs and screws should be fitted.

•  Screw the top fixing screw into position 

leaving the base of the screw head protruding 
6mm out from the wall.

•  Hook the backplate over the top screw and 

fit the bottom fixing screw into position. Do 
not fully tighten the screws at this stage, as 
the fixing holes are elongated to allow for 
out of square adjustment after the plumbing 
connections have been completed.

NOTE:

 

If entry is from the rear, the nut of the 

compression fitting will be partially behind the 
surface of the wall 

(fig.10)

This area 

MUST

 

be left clear when plastering over the pipework 
in order to make the nut accessible for future 
adjustments.

IMPORTANT: 

A suitable sealant should always 

be used to seal around the incoming pipework to 
prevent water entering the wall.

Fig.12

Fixing hole

Fixing holes

21mm

Содержание T70 GSI





























Отзывы: