background image

IVORY 4 electric shower

16

Note:

 

The preferred knob position on  

ECONOMY will give a different  
temperature to the same position on HIGH.

To decrease the shower temperature

Gradually turn the temperature control  
anti-clockwise; this will increase the flow of  
water through the shower therefore decreasing 
the water temperature.

To increase the shower temperature

Gradually turn the temperature control  
clockwise; this will decrease the flow of water 
through the shower therefore increasing the 
water temperature.

Note:

 It is advisable to be certain that the 

showering temperature is satisfactory by testing 
with your hand before stepping under the 
showerhead. There will always be a time delay of 
a few seconds between selecting a flow rate and 
the water reaching the stable temperature for 
that flow rate.

CAUTION:

 It is recommended that persons 

who may have difficulty understanding or 
operating the shower controls should not 
be left unattended while showering. Special 
consideration should be given to young 
children and the less able bodied.

W-002-A

WARNING!

After any servicing of mains water 

supply, always flush out the pipework 

to remove any debris.

Always make sure the unit is started 
on COLD in order to purge any air in 

the pipework.

Содержание IVORY 4





























Отзывы: