Trinamic TMCM-1311 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 109

Trinamic TMCM-1311 Скачать руководство пользователя страница 72

TMCM-1311 TMCL Firmware V1.11 Manual (Rev. 1.17 / 2015-NOV-05)

72

www.trinamic.com

Number Axis Parameter Description

Range [Unit]

Acc.

134

CL position
reached window

Window around the target position in which
the target position will be considered as being
reached. This value should be adjusted to the
application and the resolution of the encoder.
If the actual position is within the target
reached window for at least or longer than
defined by axis parameter 135, the

position_reached

flag will be set.

0… 255
[encoder steps]
Default = 50

RW

135

CL position
reached time

Minimum duration the motor must be within
the target reached window (axis parameter
134) before the position will be considered as
reached and

position_reached

flag will be set.

0… 131072
Default = 100
[1/10 ms]

RW

136

CL standstill
position error
gain

When the target position is reached, the
velocity regulation will be switched off and the
system is in a special standstill mode. In this
mode, the position is hold and maintained as
long as the position error is within the range
of the standstill error limit (axis parameter 138)
around the target position.
This parameter is a gain factor for the position
error used for position maintenance in
standstill mode.

A value of 20 typically provides good
results.

Higher values provide higher stiffness.

For values greater than 25 a dampening
factor > 0 (axis parameter 137) should be
used as well to prevent from oscillations.

10… 50
Default = 10

RW

137

CL standstill
position error
dampening
factor

When the target position is reached, the
velocity regulation is switched off and the
system is in a standstill mode where the
position is hold and maintained as long as the
position error is within the range of the
standstill error limit (axis parameter 138)
around the target position. Parameter 137 is a
dampening factor to prevent from oscillations
when using a high proportional gain (axis
parameter 136).

When axis parameter 136 is between 10
and 20, this parameter can be 0.

For higher proportional gain, e.g., 30, a
dampening factor of 20 is a good starting
value.

0… 65535
Default = 0

RW

138

CL standstill
position error
limit

When the target position is reached, the
position maintenance by the ramp generator is
switched off and the system is in a standstill
mode.
As long as the position error is within the
range around the target position defined by
axis parameter 138, the position maintenance
is done using parameter 136 and 137.
When the position error exceeds the range
defined by this parameter, the configured ramp
parameters are used to move back to the target
position (as in normal positioning mode).

0… +268.435.454
[µsteps]
Default=255

RW

«
...
70
71
72
73
74
...
»

Содержание TMCM-1311














































































































Отзывы:

Нет отзывов