Trinamic TMCM-1311 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 109

Trinamic TMCM-1311 Скачать руководство пользователя страница 27

TMCM-1311 TMCL Firmware V1.11 Manual (Rev. 1.17 / 2015-NOV-05)

27

www.trinamic.com

5.7.4

MVP (move to position)

The motor will be instructed to move to a specified relative or absolute position or a pre-programmed
coordinate. It will use the acceleration/deceleration ramp and the positioning speed programmed into the
unit. This command is non-blocking – that is, a reply will be sent immediately after command interpretation
and initialization of the motion controller. Further commands may follow without waiting for the motor
reaching its end position. The maximum velocity and acceleration are defined by axis parameters #4 and #5.

U

NITS AND

R

ANGE

Open loop:

t

he range of the MVP command is 32 bit signed (−2.147.483.648… +2.147.483.647).

The unit is

microsteps.

Closed loop:

t

he range of the MVP command is 32 bit signed (−2.147.483.648… +2.147.483.647).

The unit is

encoder steps.

Positioning can be interrupted using MST, ROL or ROR commands.

T

HREE OPERATION TYPES ARE AVAILABLE

:

Moving to an absolute position in the

range from −2.147.483.648… +2.147.483.647

.

Starting a relative movement by means of an offset to the actual position. In this case, the new resulting
position value must not exceed the above mentioned limits, too.

Moving the motor to a (previously stored) coordinate (refer to SCO for details).

Please note, that the distance between the actual position and the new one should not be more than
2.147.483.647 (2

31

-1) microsteps resp. encoder steps. Otherwise the motor will run in the opposite direction

in order to take the shorter distance.
When moving to a coordinate, the coordinate has to be set properly in advance with the help of the SCO,
CCO or ACO command.

Internal function:

A new position value is transferred to the axis parameter #0 (target position).

Related commands:

SAP, GAP, SCO, CCO, GCO, MST

Mnemonic:

MVP <ABS|REL|COORD>, 0, <position|offset|coordinate number>

Binary representation:

INSTRUCTION NO.

TYPE

MOT/BANK

VALUE

4

0 ABS – absolute

<motor>

0

*

<position>

−2.147.483.648…

+2.147.483.647

1 REL – relative

<offset>

−2.147.483.648…

+2.147.483.647

2 COORD – coordinate

<coordinate number>

0… 20

* Motor number is always O as only one motor is involved

Reply in direct mode:

STATUS

VALUE

100 – OK

don’t care

«
...
25
26
27
28
29
...
»

Содержание TMCM-1311














































































































Отзывы:

Нет отзывов