Trillium Roto-Jet R11 Скачать руководство пользователя страница 7

Страница: 7 / 35

R11 2x2

2.2 RECOMMENDED TOOLS

, Continued

Item

No.

Description

Qty

Part No.

PURCHASED TOOLS

Socket 5/16" Hex Bit x 3/8" Drive

060095060

Eyebolt With Nut 3/8-16

0661979

Tension Tester - V-Belt

060095057

Scriber

060095045

Temperature Stick 150°

060095047

Temperature Stick 175°

060095048

Bearing Heater (120V/60Hz)

060095046

Torque Wrench 5-80 ft-lbs.

060095026

Torque Wrench 30-250 ft.lbs.

060095027

Depth Micrometer - 0.3", 6" Base

060095051

Indicator, Test Dial .0005

060095053

Magnetic Base - Test Indicator

060095054

Bearing Separator - Spread 1/2" to 8-5/8"

060095022

Puller - 17.5 ton, 9-1/2" Reach

1 pair

060095023

Puller - 17.5 ton, 16-1/2" Reach

1 pair

060095025

Protector, Shaft (Puller)

060095037

2.2.1. Assembly Stands

Item

No.

Description

Qty.

Part No.

Pump Assembly Stand Kit (Includes stand &

swivel hoist ring)

060580652-K1

Rotor Assembly Stand

0665443-03

Ring, Swivel Hoist (D-Ring)

0667025

Assembly stand can be used for all Roto-Jet pumps.

Содержание Roto-Jet R11




































Результаты поиска

Содержание Roto-Jet R11

Отзывы:

Похожие инструкции для Roto-Jet R11

Бренды по названию

Популярные бренды

Trillium Roto-Jet R11, Руководство по разборке и сборке

Результаты поиска

Содержание Roto-Jet R11

Отзывы:

Похожие инструкции для Roto-Jet R11

Бренды по названию

Популярные бренды