Trillium Roto-Jet R11 Скачать руководство пользователя страница 32

Страница: 32 / 35

R11 2x2

6.4.2. Placing Orders

- The satisfactory ordering and receiving of parts is dependent upon

specific and correct information supplied by the purchaser. A specification sheet for

each unit manufactured is on file at the factory, and in case some special part is

needed, it can be provided if the correct model and serial number is given. Many

unnecessary errors and delays may be eliminated by observing the following

instructions.

Your parts order should state:

1. Model and serial number of pump.

2. Part number, description, and quantity required.

3. Your company name, address and zip code clearly.

4. Specific shipping and billing instructions.

5. Date required.

With this assistance, the time required to expedite your order will be greatly

reduced.

Note

: Parts will be furnished in original materials unless specified as a

material change. All material substitutions should be discussed with the

factory.

6.4.3. Assistance

- Should you need any assistance, please contact the factory or nearest

regional office listed on the back cover.

Содержание Roto-Jet R11




































Результаты поиска

Содержание Roto-Jet R11

Отзывы:

Похожие инструкции для Roto-Jet R11

Бренды по названию

Популярные бренды

Trillium Roto-Jet R11, Руководство по разборке и сборке

Результаты поиска

Содержание Roto-Jet R11

Отзывы:

Похожие инструкции для Roto-Jet R11

Бренды по названию

Популярные бренды