TRI tool BEVELMASTER 214B Скачать руководство пользователя страница 5

Страница: 5 / 58

Model 214B BEVELMASTER

92-1500 : Rev. 140425

Remove adjusting keys and wrenches before applying power to the equipment. De-

velop a habit of checking the tool before turning it on to make sure that all keys and

wrenches have been removed.

Do not force tools. Tools and tool bits function better and safer when used at the

feed and speed rate for which they were designed.

Do not reach into rotating equipment. Do not reach into the rotating head stock to

clear chips, to make adjustments, or to check surface finish. A machine designed to

cut steel will not stop for a hand or an arm.

Handle chips with care. Chips have very sharp edges and are hot. Do not try to pull

chips apart with your hands; they are very tough.

Avoid unintentional starts. Do not carry or handle tools with your hand on the

operating switches or levers. Do not lay the tool down in a manner that will start the

drive. Do not allow the tool to flip around or move when adjusting or changing tool

bits.

Store idle tools properly. Disconnect tools from the power source and store in a safe

place. Remove tool bits for safe handling of the tool.

Содержание BEVELMASTER 214B



























































Результаты поиска

Содержание BEVELMASTER 214B

Отзывы:

Бренды по названию

Популярные бренды

TRI tool BEVELMASTER 214B, Руководство пользователя

Результаты поиска

Содержание BEVELMASTER 214B

Отзывы:

Бренды по названию

Популярные бренды