TRI tool BEVELMASTER 214B Скачать руководство пользователя | Manualshive

Страница: 24 / 58

background image

24

TRI TOOL INC.

92-1500 : Rev. 140425

Adjust the cutting speed by rotating the air flow control valve at the air

connection.

Feeding the Tool Bit Into the Work

Rotate the feed handle clockwise to bring the tool bit(s) and pipe closer

together.

The machining operation begins when the first tool bit contacts the pipe.

If the pipe end is not square to the pipe axis, the tool bit will contact only a

small segment of the pipe during each revolution.

To avoid tool bit damage, the feed rate should be very slow until all of the tool

bit(s) are in contact with the pipe continually during at least one full revolution.

Continue rotating the feed handle clockwise until the end of the pipe is

completely machined.

The axial feed rate of the tool bit is .0023” (.06 mm) for each graduation or

.083” (2.11 mm) for each complete revolution of the feed handle.

Continue machining until the end of the pipe has a complete prep.

Discontinue feed and allow the head to rotate 1 to 3 revolutions to improve

finish of the prep surface.

Release the trigger to stop the head rotation.

Feed Handle

Timing Mark

Graduation Mark

Feed Handle

«
...
22
23
24
25
26
...
»

Содержание BEVELMASTER 214B



























































Отзывы:

Нет отзывов

Похожие инструкции для BEVELMASTER 214B

Бренд: TE Connectivity Страницы: 7

Бренд: Far Tools Страницы: 33

Бренд: Garland Страницы: 16

Бренд: Everwin Страницы: 12

FATMAX SFMCS650

Бренд: Stanley Страницы: 12

Бренд: Hilti Страницы: 191

Бренд: 9circle Страницы: 7

Бренд: Chicago Electric Страницы: 8

CoreMax SCFTP0620

Бренд: FasTest Страницы: 2

Бренд: Eastwood Страницы: 8

Бренд: Weller Страницы: 6

Бренд: Black Ridge Страницы: 16

Orwak 5030 Series

Бренд: Tomra Страницы: 8

Бренд: Milwaukee Страницы: 11

Бренд: Meec tools Страницы: 30

Бренд: Greatneck Страницы: 4

Бренд: Savio Страницы: 2

SDE-SA 2389861-1

Бренд: TE Connectivity Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды