TRI tool BEVELMASTER 214B страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 58

background image

19

Model 214B BEVELMASTER

®

92-1500 : Rev. 140425

NOTE:

CONFIGURATION

Jaw Blocks

Select the recommended ramps, jaw blocks and adapters for the pipe size to

be machined.

Install the ramps, adapters and jaw blocks as required onto the mandrel.

Loosen the draw nut to retract the jaw blocks to a diameter smaller then the

ID of the pipe to be prepped.

Install the mandrel assembly into the pipe.

In order to avoid cutting the jaw blocks during the machining operation, the

mandrel must be installed beyond the end preparation location.

Tighten the draw nut to force the jaw blocks out to the ID of the pipe or tube.

Tool Bits

Attach the tool holders in the appropriate position. Select the tool bit(s)

required to machine the pipe for the configuration desired.

Final Prep Location

Mandrel Assembly

Pipe

Jaw Block

Draw Nut

Draw Nut Location

«
...
17
18
19
20
21
...
»

Содержание BEVELMASTER 214B



























































Отзывы:

Нет отзывов

Похожие инструкции для BEVELMASTER 214B

Бренд: Omega Страницы: 8

Бренд: CAME Страницы: 2

Бренд: Dafra Страницы: 4

Бренд: Fein Страницы: 117

Бренд: Fein Страницы: 103

Бренд: kincrome Страницы: 12

Бренд: Eastwood Страницы: 20

Бренд: Gianni Страницы: 6

Бренд: Woodstar Страницы: 116

Бренд: REED Страницы: 2

Бренд: Matatakitoyo Torque Tools Страницы: 2

Бренд: Fein Страницы: 118

Бренд: Facom Страницы: 2

Бренд: Grad-M Страницы: 28

CAT-HT-182-2430-11

Бренд: Samtec Страницы: 4

Бренд: Far Tools Страницы: 23

Бренд: Makita Страницы: 24

Бренд: Makita Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды