manualshive.com logo in svg

TRI tool BEVELMASTER 214B, Руководство пользователя

Поделиться
Скачать
TRI tool BEVELMASTER 214B Скачать руководство пользователя страница 20

20

TRI TOOL INC.

92-1500 : Rev. 140425

NOTE:

NOTE:

Use of dull or improperly designed tool bits or tool bits not manufactured by 

TRI TOOL Inc. may result in poor performance and may constitute abuse of 

this machine and therefore voids the TRI TOOL Inc. factory warranty.

When performing any separate machining operation such as facing, beveling 

or counterboring, the tool bit should be installed in the correct tool bit holders.

The beveling tool bit should be installed in the steel tool holder.

Tool Bit Installation

Tool Holder 

(Aluminum)

Cutting Edge, Tool 

Bit Beveling

Rotation

Cutting Edge, Tool Bit 

Counterbore (Deburring)

Tool Holder 

(Steel)

When performing any multiple machining operation such as facing, beveling, 

and/or counterboring, the counterbore tool bit should be installed to ‘lead’ the 

bevel tool bit.

Insert the tool bit(s) into the slot(s) in the tool holder(s).

The cutting edge of the tool bit(s) must be on the radial centerline.

Ensure that the tool bit is not installed backwards.

Cutting Edge, Tool Bit 

Facing (Land)

Содержание BEVELMASTER 214B



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды