TRI tool BEVELMASTER 214B Скачать руководство пользователя | Manualshive

Страница: 18 / 58

background image

18

TRI TOOL INC.

92-1500 : Rev. 140425

NOTE:

SETUP AND OPERATION

Always read the operating instructions carefully/completely before operating the

Model 214B BEVELMASTER

®

.

When operating any/all Tri Tool Inc. equipment follow the 'Note' statements through

the manual for equipment safety and the ‘Warning’ and/or ‘Caution’ notes for opera-

tor safety.

A FRL (Filter/Regulator/Lubricator) is required to protect the warranty on all TRI

TOOL INC. air or hydraulic driven tools.

The motor warranty is void if damage occurs from contaminated air or lack of

lubrication.

The FRL unit must be maintained as specified in the manual. The frequency

depends on the basic air supply. Keep the water trap drained, filter cleaned

and the lubricator oil reservoir filled so there's a drop of oil every two (2) to

five (5) seconds.

If the unit is to be left idle for 24 hours or more after being run on ‘wet’ air, it is

advisable to squirt oil directly into the air motor inlet and run the motor for two

(2) to three (3) seconds. This will prevent rusting and ‘freezing’ of the rotor

vanes.

For Hydraulic Motors refer to their ‘Operator’s Manual’ for specifics.

When the unit is operated in the vertical position, cutting head up, it should be turned

upside down and the chips and/or other debris removed after each cutting operation

has been completed.

Tool life may be severely shortened, unless chips and/or other debris that

have been deposited on the cutting head during the machining operation are

removed.

«
...
16
17
18
19
20
...
»

Содержание BEVELMASTER 214B



























































Отзывы:

Нет отзывов

Похожие инструкции для BEVELMASTER 214B

Бренд: yellow jacket Страницы: 2

Бренд: Parkside Страницы: 45

Бренд: Far Tools Страницы: 22

Bravo 3-in-1 Potty

Бренд: VONROC Страницы: 24

Бренд: Carlyle Tools Страницы: 16

Бренд: Senco Страницы: 32

Бренд: Roebuck Страницы: 16

Бренд: Harbor Breeze Страницы: 3

Бренд: Lux Tools Страницы: 36

Бренд: Larzep Страницы: 8

Бренд: Powersmart Страницы: 17

Бренд: Urrea Страницы: 20

Бренд: YATO Страницы: 104

Бренд: Parkside Страницы: 96

Бренд: Matrix Страницы: 46

Бренд: SATA Страницы: 74

HellermannTyton E4500

Бренд: Spirent Страницы: 8

Aeroquip ET3000

Бренд: Danfoss Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды