manualshive.com logo in svg

TRI tool BEVELMASTER 214B, Руководство пользователя

Поделиться
Скачать
TRI tool BEVELMASTER 214B Скачать руководство пользователя страница 4

4

TRI TOOL INC.

92-1500 : Rev. 140425

TOOL CARE

Maintain tools with care.  Keep tools in good operating condition.  Sharp tool bits 

perform better and safer than dull tool bits.  Well maintained tools function properly 

when needed.

Check for damaged parts.  If a tool has malfunctioned, been dropped or hit, it 

must be checked for damage.  Run no-load tests and feed function checks.  Do a 

complete visual inspection.

Electric motors.  Use only with proper AC voltage power sources and observe all 

normal electric shock hazard procedures.

Do not abuse power and control cords.  Pulling or running over cords and cables can 

result in electrical shock hazards and malfunctions.  Keep control and power cords 

out of all cutting fluids and water.

Hydraulic drives.  Observe proper procedures for electrically driven power sources.  

Avoid damage to hydraulic lines.  Keep quick-disconnects clean.  Grit contamination 

causes malfunctions.

Air tools.  Check the exhaust muffler.  Broken or damaged mufflers can restrict 

air flow or cause excessive noise.  Use air motors only with a filtered, lubricated 

and regulated air supply.  Dirty air, low-pressure air or over pressure air will cause 

malfunctions, including delayed starting.

AREA EQUIPMENT

Secure work.  Whenever possible use clamps, vises, chains and straps to secure 

pipe.

Make sure the tool is secured; it is safer to have both hands free to operate the tool.

TOOL USE

Use the right tool and tool bit for the job.  Do not use a tool, which is incorrect for the 

job you are doing.

Keep the tool bits fully engaged in the tool bit holders.  Loose bits are a safety 

hazard.

Disconnect the power supply during setup and maintenance.  Use all 'Stop' or 'Shut 

off' features available when changing or adjusting tool bits, maintaining the tool, or 

when the tool is not in use.

Содержание BEVELMASTER 214B



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды