TRENDnet TI-G160WS Скачать руководство пользователя страница 93

Страница: 93 / 148

TRENDnet User’s Guide

Industrial Managed Switch Series

if-range

dhcp-snooping host

This command configures the
maximum host count for the
specific ports.

if-range

no dhcp-snooping host

This command configures the
maximum host count to default for
the specific ports.

if-range

dhcp-snooping trust

This command configures the trust
port for the specific ports.

if-range

no dhcp-snooping trust

This command configures the un-
trust port for the specific ports.

Example:

[DEVICE_NAME]#configure terminal

[DEVICE_NAME](config)#dhcp-snooping enable

[DEVICE_NAME](config)#dhcp-snooping vlan 1

[DEVICE_NAME](config)#interface 1/0/1

[DEVICE_NAME](config-if)#dhcp-snooping trust

Web Configuration

DHCP Snooping

Security > IP Source Guard > DHCP Snooping > DHCP Snooping

Parameter

Description

State

Select Enable to use DHCP snooping on the Switch. You still
have to enable DHCP snooping on specific VLANs and specify
trusted ports.

Note: The Switch will drop all DHCP requests if you enable
DHCP snooping and there are no trusted ports.

Select Disable to not use DHCP snooping.

VLAN State

Select Add and enter the VLAN IDs you want the Switch to
enable DHCP snooping on. You can designate multiple VLANs
individually by using a comma (,) and by range with a hyphen (-

Select Delete and enter the VLAN IDs you no longer want the
Switch to use DHCP snooping on.

Apply

Click Apply to take effect the settings.

Refresh

Click Refresh to begin configuring this screen afresh.

DHCP Snooping Status

DHCP Snooping

State

This field displays the current status of the DHCP snooping
feature, Enabled or Disabled.

Enabled on VLAN

This field displays the VLAN IDs that have DHCP snooping
enabled on them. This will display None if no VLANs have been
set.

Содержание TI-G160WS




















































































































































Результаты поиска

Содержание TI-G160WS

Отзывы:

TRENDnet TI-G160WS, Руководство пользователя, Страница: 93 / 148

Результаты поиска

Содержание TI-G160WS

Отзывы: