TRENDnet TI-G160WS Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 148

TRENDnet TI-G160WS Скачать руководство пользователя страница 49

© Copyright 2019 TRENDnet. All Rights Reserved.

TRENDnet User’s Guide

Industrial Managed Switch Series

46

(Default:auto)

interface

igmp-immediate-leave

This command enables the IGMP Snooping
immediate leave function for the specific
interface.

interface

no igmp-immediate-
leave

This command disables the IGMP Snooping
immediate leave function for the specific
interface.

Example:

[DEVICE_NAME](config)#igmp-snooping enable

[DEVICE_NAME](config)#igmp-snooping vlan 1

[DEVICE_NAME](config)#interface 1/0/1

[DEVICE_NAME](config-if)#igmp-immediate-leave

[DEVICE_NAME](config-if)#igmp-querier-mode fixed

[DEVICE_NAME](config-if)#igmp-snooping group-limit 20

Web Configuration

General Settings

Advanced Settings > IGMP Snooping > IGMP Snooping > General Settings

Parameter

Description

IGMP

Snooping

State

Select Enable to activate IGMP Snooping to forward group
multicast traffic only to ports that are members of that group.
Select Disable to deactivate the feature.

IGMP

Snooping

VLAN State

Select Add and enter VLANs upon which the Switch is to perform
IGMP snooping. The valid range of VLAN IDs is between 1 and
4094. Use a comma (,) or hyphen (-) to specify more than one
VLANs. Select Delete and enter VLANs on which to have the
Switch not perform IGMP snooping.

Unknown
Multicast Packets

Specify the action to perform when the Switch receives an
unknown multicast frame. Select Drop to discard the frame(s).
Select Flooding to send the frame(s) to all ports.

«
...
47
48
49
50
51
...
»

Содержание TI-G160WS





















































































































































Отзывы:

Нет отзывов