TRENDnet TI-G160WS Скачать руководство пользователя страница 80

Страница: 80 / 148

TRENDnet User’s Guide

Industrial Managed Switch Series

CLI Configuration

Node

Command

Description

enable

show pd-alive

This command displays the
configuration of the PD Alive Check.

configure

pd-alive (disable|enable)

This command disables or enables
the global PD Alive Check for the
Switch.

interface

pd-alive action
(reboot|alarm|all|none)

This command configures the
action when the system detects
that the host cannot respond the
keep-a-live probe packet.

interface

pd-alive interval VALUE

This command configures the
interval to send the keep-a-live
probe packets to check if the host is
still alive for the specific port.

interface

pd-alive ip IP_ADDR

This command configures the Host
IP address which connects to the
specific port.

interface

pd-alive retry-time VALUE

This command configures the retry
times when no response from the
host for the keep-a-live probe
packet for the specific port.

interface

pd-alive power-off-time VALUE
startup-time VALUE

This command configures the
power-off time and startup time.

Web Configuration

Advanced Settings > PoE > PD Alive Check

Parameter

Description

State

Enables/Disables the PD Alive Check.

Port

Selects a port or a range of ports which you want to configure.

State

Enables/Disables the PD Alive Check for the specific port(s).

IP Address

Specifies the Host IP address which connects to the port.

Interval

The interval to send the packet probes to check if the host is
still alive.

Retry Time

The retry times when no response from the host for the keep-
alive probe packet.

Action

The action to the Power Device when the system detects that
the Power Device cannot respond the keep-a-live probe packet.
The options have Reboot / Alarm / All /None.

Содержание TI-G160WS




















































































































































Результаты поиска

Содержание TI-G160WS

Отзывы:

TRENDnet TI-G160WS, Руководство пользователя, Страница: 80 / 148

Результаты поиска

Содержание TI-G160WS

Отзывы: