TRENDnet TI-G160WS Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 148

TRENDnet TI-G160WS Скачать руководство пользователя страница 15

© Copyright 2019 TRENDnet. All Rights Reserved.

TRENDnet User’s Guide

Industrial Managed Switch Series

12

Switch Installation

DIN-Rail Installation

The site where the switch will be installed may greatly affect its performance. When
installing, consider the following pointers:

Note: The switch model may be different than the one shown in the example
illustrations.



Install the switch in the appropriate location. Please refer to the technical
specifications at the end of this manual for the acceptable operating temperature
and humidity ranges.



Install the Switch in a site free from strong electromagnetic field generators (such
as motors), vibration, dust, and direct exposure to sunlight.



Install the switch in a location that is not affected by strong electromagnetic field
generators (such as motors), vibration, dust, and direct sunlight.



Leave at least 10cm of space at the front and rear of the switch for ventilation.

Fasten the DIN-Rail bracket to the rear of the switch using the included
fasteners/screws.
Note: The DIN-Rail bracket may already be installed to your switch when received.

The movable clip at the top of the DIN-Rail bracket should be on top.

The switch can be installed to a 35mm (W) DIN-Rail located in cabinet, rack, or
enclosure.

To mount the switch to a DIN-Rail using the attached DIN-Rail bracket, position the
switch in front of the DIN-Rail and hook the bracket over the top of the rail.
Then rotate the switch downward towards the rail until your hear a click indicating the
bracket is secure and locked into place.

To unmount the switch from the DIN-Rail, slightly pull the switch downwards to clear
the bottom of the DIN-Rail and rotate away from DIN-Rail to unmount.

«
...
13
14
15
16
17
...
»

Содержание TI-G160WS





















































































































































Отзывы:

Нет отзывов