TRENDnet TI-G160WS Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 148

TRENDnet TI-G160WS Скачать руководство пользователя страница 128

© Copyright 2019 TRENDnet. All Rights Reserved.

TRENDnet User’s Guide

Industrial Managed Switch Series

125

Password

User

Authority

This field displays the associated group.

Action

Click the Delete button to remove the user account.

Note: You cannot delete the last admin accounts.

Device Management

Link Layer Discovery Protocol (LLDP)

Management > Device Management > Link Layer Discovery Protocol (LLDP)

The Link Layer Discovery Protocol (LLDP) specified in this standard allows stations
attached to an IEEE 802® LAN to advertise, to other stations attached to the same IEEE
802 LAN, the major capabilities provided by the system incorporating that station, the
management address or addresses of the entity or entities that provide management of
those capabilities, and the identification of the station’s point of attachment to the IEEE
802 LAN required by those management entity or entities.

The information distributed via this protocol is stored by its recipients in a standard
Management Information Base (MIB), making it possible for the information to be
accessed by a Network Management System (NMS) using a management protocol such
as the Simple Network Management Protocol (SNMP).

Default Settings

The LLDP on the Switch is disabled.

Tx Interval : 30 seconds.

Tx Hold

: 4 times.

Time To Live

: 120 seconds.

Port Status Port Status

---- ------- ------

-------

1 Enable 2

Enable

3 Enable 4

Enable

5 Enable 6

Enable

7 Enable 8

Enable

9 Enable 10

Enable

11 Enable 12

Enable

13 Enable 14

Enable

15 Enable 16

Enable

CLI Configuration

Node

Command

Description

enable

show lldp

This command displays the LLDP configurations.

enable

show lldp neighbor

This command displays all of the ports’ neighbor
information.

configure lldp

(disable|enable)

This command globally enables / disables the LLDP
function on the Switch.

configure lldp tx-interval

This command configures the interval to transmit
the LLDP packets.

configure lldp tx-hold

This command configures the tx-hold time which
determines the TTL of the Switch’s message.
(TTL=tx-hold * tx-interval)

«
...
126
127
128
129
130
...
»

Содержание TI-G160WS





















































































































































Отзывы:

Нет отзывов