manualshive.com logo in svg

Trebor QUANTUM NXT, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Trebor QUANTUM NXT Скачать руководство пользователя страница 36

 

 

 

 

PAGE 36 

QUANTUM NXT DI HEATER OPERATION / MAINTENANCE MANUAL 

 

Table 7-2: Visual Inspection Details

 

 

ITEM

 

DETAILS

 

Plumbing Leaks

 

Visually check DI water lines outside of heater cabinet for signs of leaks at the 
connections.  (A leak sensor will detect leaks, but this periodic visual check is 
recommended.)  Also, visually check bottom of cabinet inside heater module 
enclosure for DI water leaks.  Tighten fitting(s) if necessary.  If heater module 
is leaking, contact Trebor for instructions.

Over-pressure Relief 
Valve

 

Visually check the drain line for water running from the heater.  The over- 
pressure relief valve is factory set to open at 60PSIG.   If pressure is less than 
60 PSIG and water is still running through the relief drain, the valve may need 
adjustment or replacement.

General Electronics

 

Visually check electronics inside control enclosure for any signs of 
overheating, deformation, or corrosion. 

Solid State Relays

 

The SSR’s should be free of corrosion at the terminals and should not have 
signs of overheating or deformation.  The wires attached to the SSR’s should 
be clean and in good condition.  Check and tighten mounting screws for 
optimum heat transfer to heatsink.

Main Circuit Breaker

 

The main circuit breaker should be checked for signs of loose connections at 
the termination lugs.  Damaged lugs should be replaced by Trebor qualified 
personnel.  The terminals should be checked for tightness. 

Distribution Breakers

 

& Contactors

 

The distribution breakers and contactors should be checked for signs of loose 
connections at termination lugs.  Damaged lugs should be replaced by Trebor 
qualified personnel.  The terminals should be checked for tightness. 

Branch Circuit 
Breakers

 

These should be checked for signs of loose connections at the termination 
lugs.  The terminals should be checked for tightness. 

Process Fluid 
Thermocouples

 

Recommend removing and inspecting thermocouples for any signs of wear, 
cracking or rupture at tip. Replace any thermocouple that exhibits any of these 
signs. 

Содержание QUANTUM NXT








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды