manualshive.com logo in svg

Trebor QUANTUM NXT, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Trebor QUANTUM NXT Скачать руководство пользователя страница 19

 

 

 

 

 QUANTUM NXT DI HEATER OPERATION / MAINTENANCE MANUAL 

PAGE 19 

 

 

 

 

 

3.3.b  Ethernet Communication

 

For remote monitoring and control of the heater, plug an Ethernet cable 
into the RJ45 connector on the rear connection panel of the system. See 
appendix. 

 

3.4  GENERAL

 

After completion of Section 3.3, refer to the touch screen for heater 
operation. Once DI water is flowing through the system and power is 
turned on, a process temperature can be selected and power switched on 
to the heater modules.  The controls will do the rest. 

 

If there is a problem with the DI water heater, the system controller will 
notify the operator that the heater requires attention. After the fault 
condition is corrected, the heater can be reset using the RESET button 
located on the heater door (the fault condition will also be cleared if the 
entire system power is cycled off and on).  Redundant hardware relay 
interlocks back up heater element temperature, leak sensor, and 
component temperature faults. 

 

3.5  TOUCH SCREEN

 

A touch screen provides an intuitive interface to the DI water heater.  The 
heater can also be operated using both hardware and software remote 
interfaces (depending on the heater options).  The display is divided into 
several pages. 

 

 

3.5.a  Home Page

 

 

 

 

Figure 3-2: Home Page

 

NOTE: 

Before starting the system, it is important to become familiar with 

Section 4, Operation.  Only trained, qualified, authorized, personnel 
should operate this system. 

Содержание QUANTUM NXT








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды