background image

BAS-SVN208G-EN

7

Step 11: Air-Fi

®

 Wireless Setup

sensor.

• If mounting onto sheetrock or plaster, use the plastic threaded anchors (pre-drilling 

holes is not usually necessary) and the two M3.5 x 20 mm mounting screws.

• For mounting onto an electrical junction box, use the two 6-32 x 3/4 in. screws. 

Air-Fi

®

 Addressing

Air-Fi addressing of WCS and WCI determines which devices can communicate on an 
Air-Fi network. 

GRP and NET must be set the same for all WCS and WCI on the 

Air-Fi network. 

WCS address is configured on the sensor’s display. 

WCS Address 

must match the appropriate unit controller rotary address setting. 

See Air-Fi 

WCS Configuration Instructions X3964126601 or Air-Fi WCS Quick Reference Guide 
BAS-SVU029*-EN for more information. 

Figure 1.

Air-Fi addressing example: WCIs and WCSs

Establishing an Air-Fi

®

 Network

When all aspects of hardware installation are complete, you are ready to power up the 
system and establish the wireless network.

Best Practice: Power up all devices in the network at the same time. If you are 
unable to do this, power them up in the following order: 

1. All WCIs.
2. All unit controllers: UC210, UC400, UC600, BCI-I, BCI-R.
3. The System Controller.
4. WCSs, if present.

Note: 

If the coordinator WCI is powered up 1 hour or more before the other devices on 

the network, then you must open the network manually or with Tracer TU.

Automatic Network Formation and Sensor Association

A WCI that is connected to a System Controller is auto-assigned as the network 
coordinator. The coordinator WCI allows all WCIs and WCSs having matching addresses 
to automatically join the network. (For more details about the process of network 
establishment, see the Air-Fi

®

 Wireless System IOM (BAS-SVX40).

After the network is formed, WCSs automatically associate with their designated 
controllers.

UC/BCI

System 

Controller

UC/BCI

WCI

WCI

GRP  NET

 NET

GRP  NET

1

1

1

1

1

WCI

1

2

GRP

1

Sn: 1

 

UC: 101

 

Network 1

101

102

Sn: 1

UC: 102

gn: 11

gn: 11

Group 

a

nd

network

a

ddresses 

must m

a

t

c

h.

UC/BCI

a

ddresses

must 
m

a

t

c

h.

WCS

WCS

1

2 3 4

5

6

78

9

0

NET

GRP

1

2 3 4

5

6

78

9

0

WCI 

a

ddress

i

ng

Содержание Tracer Concierge

























Отзывы: