background image

©2022 Trane

 CVRF-SVN005C-EN

Introduction

Read this manual thoroughly before operating or servicing this 
unit.

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as required. 
Your personal safety and the proper operation of this machine 
depend upon the strict observance of these precautions.

The three types of advisories are defined as follows:

WARNING

Indicates a potentially hazardous 

situation which, if not avoided, could 

result in death or serious injury.

CAUTION

s

Indicates a potentially hazardous 

situation which, if not avoided, could 

result in minor or moderate injury. It could 

also be used to alert against unsafe 

practices.

NOTICE

Indicates a situation that could result in 

equipment or property-damage only 

accidents.

Important Environmental Concerns

Scientific research has shown that certain man-made 
chemicals can affect the earth’s naturally occurring 
stratospheric ozone layer when released to the atmosphere. In 
particular, several of the identified chemicals that may affect 
the ozone layer are refrigerants that contain Chlorine, Fluorine 
and Carbon (CFCs) and those containing Hydrogen, Chlorine, 
Fluorine and Carbon (HCFCs). Not all refrigerants containing 
these compounds have the same potential impact to the 
environment. Trane advocates the responsible handling of all 
refrigerants-including industry replacements for CFCs and 
HCFCs such as saturated or unsaturated HFCs and HCFCs.

Important Responsible Refrigerant 

Practices

Trane believes that responsible refrigerant practices are 
important to the environment, our customers, and the air 
conditioning industry. All technicians who handle refrigerants 
must be certified according to local rules. For the USA, the 
Federal Clean Air Act (Section 608) sets forth the requirements 
for handling, reclaiming, recovering and recycling of certain 
refrigerants and the equipment that is used in these service 
procedures. In addition, some states or municipalities may 
have additional requirements that must also be adhered to for 
responsible management of refrigerants. Know the applicable 
laws and follow them.

WARNING

Proper Field Wiring and Grounding 

Required!

Failure to follow code could result in death or serious 

injury. All field wiring MUST be performed by qualified 

personnel. Improperly installed and grounded field 

wiring poses FIRE and ELECTROCUTION hazards. To 

avoid these hazards, you MUST follow requirements for 

field wiring installation and grounding as described in 

NEC and your local/state/national electrical codes. 

 

WARNING

Personal Protective Equipment (PPE) 

Required!

Failure to wear proper PPE for the job being undertaken 

could result in death or serious injury. Technicians, in 

order to protect themselves from potential electrical, 

mechanical, and chemical hazards, MUST follow 

precautions in this manual and on the tags, stickers, 

and labels, as well as the instructions below:

Before installing/servicing this unit, technicians 
MUST put on all PPE required for the work being 
undertaken (Examples; cut resistant gloves/sleeves, 
butyl gloves, safety glasses, hard hat/bump cap, fall 
protection, electrical PPE and arc flash clothing). 
ALWAYS refer to appropriate Safety Data Sheets 
(SDS) and OSHA guidelines for proper PPE.

When working with or around hazardous chemicals, 
ALWAYS refer to the appropriate SDS and OSHA/GHS 
(Global Harmonized System of Classification and 
Labeling of Chemicals) guidelines for information on 
allowable personal exposure levels, proper 
respiratory protection and handling instructions.

If there is a risk of energized electrical contact, arc, or 
flash, technicians MUST put on all PPE in accordance 
with OSHA, NFPA 70E, or other country-specific 
requirements for arc flash protection, PRIOR to 
servicing the unit. NEVER PERFORM ANY 
SWITCHING, DISCONNECTING, OR VOLTAGE 
TESTING WITHOUT PROPER ELECTRICAL PPE AND 
ARC FLASH CLOTHING. ENSURE ELECTRICAL 
METERS AND EQUIPMENT ARE PROPERLY RATED 
FOR INTENDED VOLTAGE.

Содержание Symbio CVRF

















































Отзывы: